Specifications subject to change without notice. Digital Light Processing and DLP are trademarks of Texas Instrumets. Attachment plate . . . . Angle adjuster...... Adjuster pole A ..... Adjuster pole B ..... Projector mount bracket Pole fixer......................1 Safety fitting....................1 Washer-fitted screws (M6 x 12).....29 Washer-fitted screws (M4 x 8).......4 Caution: Mounting should be done by a qualified technician. Make sure that the mounting (ceiling) area has suf

The mounting surface being used must hold the weight requirements indicated on your TV mount instruction sheet. If monitor size is greater than 27”, model PVUM must be used for added stability. NOTE: The lag bolts and washers are used to mount the bracket to the stud through the holes in the back of the ceiling plate. It may be easier to mount the plate first, before assembling the entire product. Use an 1/8” drill bit to drill pilot holes 1-/” deep. 1. Set the coupler assembly in place in the

in weight. Warning Statements WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM WEIGHT OF 40 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR T

It prevents removal of an LCD or Plasma from the mounting plate. The integrated theft-resistant clips latch the mounting bracket arms to the rod on the wall plate. A security screw then locks the pieces in place. This revolutionary design features security screws that require a custom allen wrench (included) to attach and detach the hardware. Plus, it’s backed by our industry-leading Lifetime Guarantee. Features • Fits CTM and PCM Series Display Mounts • Prevents removal of LCD or Plasma •

IF NOT, THE WALL MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION IN

Raise the front adjustment foot slightly slide the projector bracket under the foot. lower the foot snug against the bracket. Locate the 4mm mounting holes located on the bottom of the projector. Secure the mounting bracket with the two (2) 4mmx10mm min (supplied) Phillip screws tighten to (4kg-cm). The hinge pin openings must face the lens of the projector. Align the holes from the strap to the threaded points on the side of the mounting bracket and secure using the two (2) 4mmx10mm Phillip scr

Warning Statements WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MINIMUM WEIGHT OF 250 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. DO NOT PLACE A UNIT WEIGHING MORE THAN 125LBS. ON THIS MOUNT. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF

Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the display and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the display. Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use su

Includes: (2) steel chassis sleeves, (2) aircraft-grade plastic-sheathed braided-steel cables, keyed steel lock box. Cables are routed through the steel chassis sleeves. Works with PBL projector mounts. Adapter PP-SEC PP-SEC50 Additional Steel Cables For PP-SEC and PP-SEC50. Choose from 16" and 50" lengths of steel security cable. Or call inside sales at 800.368.9700 for a custom length for $1.50 per foot. Suggested List $ 5.99 $14.99 50