("Raypak") warrants to the original owner that all parts of this boiler which are actually manufactured by Raypak will be free from failure under normal use and service for the specified warranty periods and subject to the conditions set forth in this Warranty. Labor charges and other costs for parts removal or reinstallation, shipping and transportation are not covered by this Warranty but are the owner's responsibility. HEAT EXCHANGER WARRANTY: Five (5) years from date of boiler installation

FOR STANDING PILOT MODELS WITH ROBERTSHAW GAS VALVE, 2 STAGE OPERATION. (Models 90, 135 & 180) 1. STOP! Read the safety information. 2. Set the thermostat to the lowest setting. 3. Turn off all electric power to the appliance. 4. Push in and move gas control lever counterclockwise to "OFF" position. GAS CONTROL LEVER SHOWN IN "OFF" POSITION GAS INLET Fig. #8934.0 NOTE: Lever cannot be moved from "ON" to "OFF" unless lever is pushed in slightly. Do not force. 5. Wait five (5) minutes to clear out

LIGHTING INSTRUCTIONS FOR STANDING PILOT MODELS. Some safety information you need to read and under stand before operating the boiler. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This boiler has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING Smell all around the boiler area for gas. Be sure to smell next to the floor beca

#8934.0 ROBERTSHAW (All Models) 8. Turn on all electric power to the boiler. 9. Set thermostat to desired setting. 10. If the boiler will not operate, follow the instruction "To Turn Off Gas To Boiler" and call your service technician or gas supplier. TO TURN OFF GAS TO BOILER 1. Set the thermostat at the lowest setting. 2. Turn off all the electric power to the boiler if service is to be performed. 3. For Honeywell Valve: Turn gas control knob clockwise to "Off". Make sure knob rest against sto

3. For Honeywell Valve: Turn gas control knob clockwise to "Off". Make sure knob rest against stop. For Robertshaw Valve: Push in and move gas control lever to "Off" position. HONEYWELL PILOT CAUTION: Should overheating occur or the gas supply fails to shut off, DO NOT turn off or disconnect the electrical supply to the pump. Instead, shut off the gas supply at a location external to the appliance. Failure to observe this precaution may aggravate the overheated condition resulting in possible da

Inspect the vent terminal outside the building. Make sure it is not damaged to cause blockage or restriction of the flue gas. Observe for any indication of soot. The presence of soot accumulation in the vent terminal would indicate an abnormal operating condition. This should be investigated and corrected by a qualified service agency. SOOT CORROSION DISENGAGED Fig. #8204.0 3. Circulator (Water Pump) Inspection. The circulator is permanently lubricated and thus, will not require any lubrication.

A. This boiler does not have a pilot. It is equipped with a hot surface ignition device which automatically lights the burners. Do not try to light the burners by hand. B. BEFORE OPERATING smell all around the boiler area for gas. Be sure to smell next to the floor because some gases are heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS * Do not try to light any appliance. * Do not touch any electric switch; * Do not use any phone in your building. * Immediately call you

CSA 2. ASME HLW Stamp and National Board Listed 3. ISO 9001 1.5 HEAT EXCHANGER WARRANTY A. Limited five-year warranty from date of installation B. Limited twenty-year thermal shock warranty from date of installation C. Limited ten-year warranty for cupro-nickel heat exchangers only PART 2 -PRODUCTS 2.1 MANUFACTURER A. Raypak, Inc. 1. Contact: 2151 Eastman Ave., Oxnard, CA 93030; Telephone: (805) 278-5300; Fax: (800) 872-9725; Web site: 2. Product: Raytherm® copper finned-tube water heater(s) 2.2

Installation The water storage tank MUST be installed using dielectric connections. Failure to do so will void the manufacturer’s warranty. Installation of the tank without dielectric connections can cause the rapid failure of the storage tank due to electrolysis. For this reason, it is imperative that dielectric connections be utilized. The tank should be installed in such a manner that should the tank or any of its connections leak, the resulting flow of water will not cause damage. Follow the

Your results may vary. Economaster Circuit Board Catalog No.: 5100.20-I Effective: 12-28-07 Replaces: 03-15-03 ELECTRICAL DATA Adjustable Timing: 3 to 10 minutes (Factory set at 7 minutes) Input Power (Primary): 24 VAC 50/60 Hz Input Signal (Controller): 24 VAC or 120 VAC Output (SPST Relay): Load - Up to 10 Amp-120 VAC Single Phase* Ambient Temperature: -67°F to +158°F * Motors larger than 3/4 HP and three-phase current require a contactor or motor starter equipped with a 120 VAC coil