Input level RF Power Input Impedance Audio Adjust. Range Battery Dimensions Weight UHF 188 Selectable Frequencies (566.125-589.875MHz) Dual-channel ReceiverPLL Synthesized-95dBm 50Hz – 15kHz >57dB (±5kHz) “A” Weighted MIC Level – unbalanced – 3.5mm Mini-Jack -64 dBm – 600 ohms @ ± 5kHz deviation -28 dBm – 600 ohms @ ± 40kHz deviation 2 “AA” Alkaline (2 x 1.5V) - 3-4 hours runtime 2 “AA” rechargeable Ni-MH (2 x 1.2V) 6VDC @ 0.5A 2.87"W x 4.45"H x 1.59"D (73 x 113 x 40.5 mm) Approx. 10.2oz (290g)

(9) Rack ears. If you wish to use the 311DRH in a standard 19" rack by itself you can use the HR-1 rack kit and attach th. rack ears using the four supplied machine screws (two per side near front) as shown. If you wish to use th. 311DRH in a standard 19" rack with another 311DRH or a 411DRH you can use the HR-2 rack kit and attac. the rack ears using the four supplied machine screws (on the outer sides of each unit) as shown. Also attac. the joining plate (supplied) underneath the two units by

the same frequency. (8. Output (balanced. Using a suitable audio cable (not supplied) connect the XLR connector to the audio output on the receiver, an. connect the other end of the cable to the suitable mic/line input of an audio mixer or amplifier. 221R Two-channel VHF receiver. The 221R contains two VHF receivers operating on different frequencies. This allows single or simultaneou. use of two transmitters. The receiver features two 1/4-inch output jacks and two volume adjustments - one forea

Ch.1 is on the “Tip” while Ch.2 in on the “Ring”. (5) LCD Display: The twin LCD display will light up when the power is turned “ON”. The LCD displays show the following information. TV:Receive Channel Number: 30:01 – 33:47 Battery Condition: Using a 3-step indicator - 1 (Low) to 3 (High) Reception Level: Using a 4-step indicator - 1 (Low) to 4 (High) To change the TV:Receive channel number, use the tip of the tool provided and press the UP or DOWN button until the desired channel number appears

(24) Insert two fresh Alkaline* “AA” batteries* into the compartment. Make sure the battery polarity is correct as marked inside the battery compartment. *While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries. In the battery compartment you will also find #25 and #26: (25) MIC LEVEL Control: The MIC LEVEL control enables you to adjust the audio level of the microphone. Using the supplied tool, turn the dial clockwise to increase, or counterclockwise to decreas

Lecturers, Actors, Actresses, etc. Model 31IT: Instrument body-pack transmitter. Designed for electric guitar and bass. 32BT Lavalier Microphone with body-pack transmitter: (1) Open the battery compartment lid by sliding it in the direction indicated and raising it. (2) Insert one fresh Alkaline 9-volt battery into the compartment. Make sure battery polarity is correct. (3) Frequency Labe. The Frequency label indicates what frequency (in MHz) the transmitter broadcasts on. The AZDEN receive. in

Channel Selectivity . 67 dBm Intermodulation . 62 dBm Noise Reduction Expander (TOKO) Audio Output -22 dBm (balanced) @ 1 kHz ± 40 kHz Output Impedance 2 k . (balanced) S/N Ratio 57 dB (± 5 kHz) Power Reqirement 2 “AA” Batteries (Alkaline) - 6-8 hours runtime Dimensions 63W x 98H x 27D mm 2.48W x 3.86H x 1.06D inches Weight .180 g (6.35 oz) w/batteries 15BT Belt-pack Transmitter RF Power 25 mW Antenna 1/4 wavelength Frequency Response 50 Hz - 15 kHz Reference Deviation ± 5 kHz (-60 dBm - 1 kHz i

Connect an audio cable from the output o. the receiver to a mic/line input on your audio mixer or amplifier. Plug the receiver.s AC adaptor into the 12. input jack on the receiver, and then plug it into the 110-120 VAC electrical outlet. With the volume of you. mixer or amplifier set to minimum level, turn your system.s power on. Turn on the transmitter(s). Make sur. all LEDs on the receiver and transmitter(s) are operating as described in the preceding pages. Now set th. receiver.s volume to th

40-17,000Hz (– 3dB) Monitor Output ............................................ 50-17,000Hz (– 3dB) Noise Level Mic (– 50)...................................................... – 55dB Line (+0) ....................................................... – 57dB T.H.D. ............................................................ 0.15% @ 1KHz MIC Input Level Electronic Balanced .................................... – 50dBu MIC Output Level Switchable Electronic Balanced ................ +0 / – 50dBu Unb

105UPR Receiver After installing new batteries, mount the receiver to your video camera with the supplied shoe-mount or hook and loop fastener. Connect the output cable to the receiver and to the microphone input on the video camera. Switch the 105UPR to “ON” and the power indicator (7) should come on RED. If it doesn’t, check the batteries. When the 105UPR receives a signal from the transmitter the LED indicator will change to GREEN. If it does not, make sure both the receiver and the transmitt