83” (208 cm) L x 45” (113 cm) W x 61” (153 cm) H Export Crating .............................................. 131.8 cu. ft. (3.73 M.) Basket RPM ................................................. Reversing 40-3.2 reversals per minute. Non-reversing - 40. * Input ratings as shown are for elevations up to 2000 ft. (610 M). For higher elevations, ratings should be reduced 4% for each 1000 feet (305M) above sea level. Page 12 Motor List DOUBLE MOTOR MODELS Motor No. Voltage Hz. Phase Basket/Fan HP A

NATURAL GAS ONLY Check the gas pressure inlet supply to the dryer, 11 inches WC Pressure maximum. Check the manifold pressure, 3.5 inches WC Pressure inside the dryer. CAUTION Low gas pressure and intermittent gas will cause gas ignition problems and inadequate drying of the clothes load. Page 21 Steam Piping Installation INSTALLATION INSTRUCTIONS PIPING RECOMMENDATIONS 1. Set and anchor dryer in position. Machine should be level to assure proper steam circulation. 2. To prevent condensate drain

The currents listed are rated for system voltage ranges of 110 – 220 and 220 – 240. ** Rated Amperes are to be used to determine incoming conductor size and short-circuit protection. Rated amperes are figured in accordance with the 1981 NATIONAL ELECTRIC CODE, Sections 430-22 and 430-24. Table 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031 Installation Overall Dimensions and Connecting Data SCR97N OPENOPENCLOSECLOSECLOSECLOSESTEAM INLETSTEAM INLET 36-7/8 in. (93.7 c

With respect to non-durable parts normally requiring replacement in less than two (2) years due to normal wear and tear, and with respect to all new repair or replacement parts for Cissell equipment for which the two (2) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment of

THE WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. CISSELL NEITHER ASSUMES, NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT, ANY OTHER WARRANTY OR LIABILITY IN CONNECTION WITH THE MANUFACTURE, USE OR SALE OF ITS EQUIPMENT OR PARTS. For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor cannot be reached, contact Cissell. IDENTIFICATION NAMEPLATE The Identification Nameplate is located on the re

3 2 Technical data and dimensions ....................................................... 4 Technical data ................................................................................ 4 Dimensions ..................................................................................... 5 3 Installation and connection ............................................................. 6 Ground ............................................................................................ 6 Removing the tr

2. Operate dryer using full-size loads. Very large loads use extra energy. Very small loads waste energy. 3. Dry light-weight fabrics separately from heavy fabrics. You will use less energy and get more even drying results by drying fabrics of similar weight together. 4. Clean the lint screen area daily. A clean lint screen helps give faster, more economical drying. 5. Do not open the dryer door while drying. You let warm air escape from the dryer into the room. 6. Unload the dryer as soon as it

Replace Coil Assembly. Gas turned OFF. Turn Manual Gas Valve ON. Line fuse or heater circuit fuse blown to unit. Replace fuse. Defective Door Switch. Replace Door Switch. Silicon Carbide Igniter not igniting gas. Must be 3/16” to 5/16” above burner. Replace Radiant Sensor. Air Switch not operating. Clean out lint compartment daily. Check Back Draft Damper for foreign objects, lint accumulation or other causes that may prevent damper from operating. Check duct work for lint build-up. Check instal

8 Automatic lubricator The bearing house of the machine is equipped with a lubricating device (A) which automatically lubricates the bearing during one year. Upon delivery of the machine, this lubricator has not been brought into use. To this effect, please put on the matching screw (B) in the foreseen opening of the lubricator. Ignoring this instruction will inevitably cause dam age to the bearings! 9 10 3 S1...S5 Electrical connection of the liquid soap pumps The 220V can be transformed to oth

3. Dress garment on buck. 4. Simultaneously push and hold both CLOSE pushbuttons (Items 1 and 6, Figure 2) until head closes and pressing pressure is applied. Release both pushbuttons. NOTE: If either pushbutton is released BEFORE pressing pressure is applied, head will return to a fully OPEN position. 5. Once garment is sufficiently pressed, press OPEN pushbutton (Item 5, Figure 2) to open press. 6. Hang or fold pressed article as soon as possible to preserve finish. Presses With Timers ONLY 1.