GRIP HANDLE HIDDEN HANDLE . . English WARNING / SAFETY PRECAUTIONS English WARNING / SAFETY PRECAUTIONS To avoid any risk of personal injury, material damage or incorrect use of the appliance, be sure to observe the following safety precautions. (After reading these owner’s instructions, please keep them in a safe place for reference). Remember to hand them over to any subsequent owner. Warning Indicates that a danger of of death or serious injury exists Indicates that a risk of personal injury

Operate the Selector Switch to run or stop the unit. -Do not use Main Power Switch or Auxiliary Power Switch to operate unit. 2. Do not stick anything into the air outlet or inlet. -It is dangerous and it can cause injury or damage. 3. Avoid exposing your body directly to a continuous cool air - flow for long periods. -It is not good for your health. 4. Do not pour water on the unit to clean it. -It is dangerous and it can cause injury or damage. Never use solvents or harsh chemicals when cleani

2. Avoid the unit being exposed to direct sunlight. Keep direct sunlight from the room. 3. Do not leave doors and windows open. • FAN & COOLING CONTROL The Fan Control Selector Switch has six positions. Choose one of the speed settings by rotating the fan control Selector Switch to the appropriate position. CAUTION When the air conditioner has been performing its cooling operation and is turned “OFF” or set to the ‘FAN” position, wait at least 3 minutes before resetting to the cooling operation.

Всегда используйте для этих целей кнопки AIR DIRECTION и SWING. Если Вы поменяете угол наклона вручную, это может вызвать неисправность в работе кондиционера. Если ламели неправильно функционируют, отключите кондиционер и включите заново. ' Если кондиционер включается сразу же после выключения, горизонтальные ламели могут начать двигаться с задержкой в 10 секунд. ' Угол открытия горизонтальных ламелей не должен быть слишком узким, так как это может привести к снижению эффективности кондиционе

GENERAL INFORMATION ......................................................................................................11 • CHANGING AIR FLOW DIRECTION • AIR FLOW AROUND UNIT • DRAIN HOLE AND WATER DRIPPING OUTSIDE 6. CARE AND MAINTENANCE ....................................................................................................12 • AIR FILTER • CLEANING THE AIR CONDITIONER 7. ELECTRICAL REQUIREMENTS ....................................................................................

Using the hole in the top and bottom of each Window Kit Frame as a guide, secure Window Kit Frame in window sash and on the window sill. WINDOW SHUTTER WINDOW SASH WINDOW FRAME Screw (Type C) Screw (Type C) INNER WINDOW SILL 7 • Step 6 - Recheck Installation To be sure you have correctly installed your Room Air Conditioner, review the steps and make sure all of the parts are securely fastened in the window as the instructions show. A tight seal is essential. Read through the Use & Care manual to

This function is realised in the YUV domain by detecting the colours near to the skin tone. n Scan-Velocity modulation output. Also the SVM function can be activated for all incoming CVBS, Y/C and RGB/YPrPb signals. The delay between the RGB output signals and the SVM output signal can be adjusted (by means of the SVM2-SVM0 bits in subaddress 48H) so that an optimum picture performance can be obtained. Furthermore a coring function can be activated. It is possible to generate Scan Velocity Modul

. • Do not place or store laundry products on top of washer at any times. • Install the washer on the horizontal solid floor. If the washer is installed on an unsuitable floor, it could make considerable noise, vibrate severely and cause a malfunction. If the washer is not level, adjust leg up or down for horizontal installation. • Ventilation openings must not be obstructed by carpeting when the washer is installed on a carpeted floor. • Leave some space (right & left : 2cm, rear : 10cm). • In

In inserting a disc with other region code, it does not operate. Please only use a disc with region code 2 or ALL. - is a ‘DO NOT’ mark. If this mark is displayed in operating the product, please wait for a while, then use it. If " DO NOT" mark continues to be displayed in pressing a button after that, it means the button does not function in the currently played disc. - Press a product button on the REMOTE then use the product. • DVD operation : [ DVD] button • Video operation : [ VCR] button C

¦ Child-Lock The Child-Lock system has been used to prevent children from pressing any button to change the program during operation. ¦ Nano-silver sterilization washing(Option) By applying very fine silver particles on essential parts inside, the washer sterilizes up to 99.9% as is done by boiling wash. ¦ Air bubble washing(Option) This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles completel