Do not use any phone in your building. 3. Clear the room, building, or area of all occupants. 4. Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. 5. If you cannot reach your gas supplier, call the Fire Department. I nstallations must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the state, province, or region where this appliance is being installed. A WARNING 2 English IMPORTANT SAFETY

The information in this publication was derived from various sources, is provided in good faith and believed to be correct when published. Products listed in this publication are provided for the purposes of information only and reference in this publication should not be construed as an official endorsement by any of the government agencies participating in the Reach for the Stars Program. This document can be made available in alternative formats to meet the needs of people with disabilities.

Please fasten the drain hose to the drain thread of safety valve by twisting (see to Figure 3). Connect the other end of drain hose to the sewer to avoid polluting the room by splashing. When the power is switched on, and the water heater starts operating, there may be some water discharged from the pressure relief hole of safety valve. It is due to the water expansion under heating, and is normal phenomenon. The pressure relief pipe shall communicate with the air directly.Do not Connect to drai

TIME CLOCK 17:18 ON TIME 18:00 ON PROG 8 OFF TIME 23:00 SLEEP TIMER 120 REMIND TIME 19:00 REMIND PROG 18 Set up function Screen saver and childlock functions How to start screen saver function When the BACKGROUD function is ON, the screen will turn automatically as shown "NO SIGNAL" of moving . NO SIGNAL 1 Press the FUNCTION menu button, till the FUNCTION menu shown on the right display on the screen. 2 Press the CH+/- buttons to select "BACKGROUND" and press the VOL-/+ buttons to turn the BACKG

4) Press OK button to save the changes and return to Programme Timer screen. 5) Press EXIT button to give up the changes and return to Programme Timer screen. / Delete Timer You can delete the programmed timers from the timers list. 1) Press button to select Delete in the Programme Timers screen. 2) Press / button to select the timer you want to delete and press OK to delete. A pop-up confirmation window is displayed if you select Yes and press OK button. The selected timer will be deleted. / In

Company Printed in the U.S.A. D&S 1-800-448-5872 All specifications and illustrations subject to change without notice and without incurring obligations.

Press MENU button continuously, until select TUNING menu. TUNING POS EDIT ■* POS EX. ■* SEARCH UP AUTO MEMORY -► SELECT t * ADJUST *4 3. Press CH+/- button and move the indicator to SEARCH. □ <1. TUNING POS EDIT ■+ POS EX. ■+ SEARCH UP AUTO MEMORY -► SELECT t * ADJUST *4 4. Press VOL+/- button to start searching. VOL- button is used to search the lower frquency channel. VOL+ button is used to search the higher frequency channel. Repeat the steps until you find the channel you ne

Channels appointment Channels appointment MENU CH+ CHVOLVOL+ 1.Press MENU button, until TIMER appears on the screen. 2.Press CH+/- button, move the indicator( ) to CLOCK, press VOL+/- button, and you can set the time(same as TIMER OFF and it will be the TIMER CLOCK OFF TIMER ON TIMER POS 1:40 EVERY 19:00 EVERY 22:00 0 APPOINTMENT standard of the clock of APPOINTMENT). 3.Press CH+/- button, move the indicator( ) to APPOINTMENT, then press VOL+ button to enter the sub-menu. 4.Press VOL+/- button t

3.Press V+/V- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired quality has been achieved .. Functions: 1.TUNING PROGRAM: Press V+ to enter it and the TUNING PROGRAM menu appears: CHANNEL 1 EDIT NAME COLOUR SYSTEM AUTO SOUND SYSTEM DK SKIP OFF AFC ON FINE TUNE EXCHANGE MANUAL SEARCH TUNING PROGRAM 143.65MHZ CHANNEL : Press V+/V-to change the TV channel . EDIT NAME: Press V+ to enter it , then press V+/- to selec