Log:

Chicago Electric 90300

Scaricare : 0 File Size : 5 mb    Produttore : Chicago Electric  
Categoria : Energia elettrica

2. Keep the Generator and surrounding area clean at all times. 3. When spills of fuel, oil occur, they must be cleaned up immediately. Dispose of fluids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container. 4. Never store fuel or other flammable materials near the Generator. 5. Do not smoke, or allow sparks, flames or other sources of ignition around the Engine and Fuel Tank. Fuel vapors are explosive. 6. Keep grounded cond

Chicago Electric 54811

Scaricare : 1 File Size : 5 mb    Produttore : Chicago Electric  
Categoria : Altri elettrodomestici da cucina

© Copyright 2005 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS Item Description Electrical Requirements 120 Volt / 60 Hz Power Cord Length: 3’-3” Power Plug Type: 2-Prong, Polarized Inner Pot Capacity 3.5 Quarts Temperature Range 165.60° Fahrenheit (High Setting)

Chicago Electric 90236

Scaricare : 8 File Size : 4 mb    Produttore : Chicago Electric  
Categoria : Energia elettrica

(See Figure C.) 4. Check the Fuel Gauge (34) for the amount of unleaded gasoline in the Fuel Tank (32). If necessary, remove the Fuel Tank Cap (37) and refill the Fuel Tank with unleaded gasoline. Then, replace the Fuel Tank Cap. (See Figure D.) FIGURE C OIL FILL CAP FUEL GAUGE (34) FUEL TANK CAP (37) FUEL TANK (32) FIGURE D REV 11/04 SKU 90236 For technical questions, please call 1-800-444-3353. Page 13 To StartThe Generator: To StartThe Generator: . Turn the Fuel Valve (31) to its vertical “OP

Chicago Electric 44677

Scaricare : 7 File Size : 4 mb    Produttore : Chicago Electric  
Categoria : Pistole

V ~ Volts Alternating Current A Amperes no load xxxx per min. No Load Revolutions per Minute SKU 44677 For technical questions, please call 1-800-444-3353. Page 7 Preparing to Paint Painting Tips: Successful spray painting is a skill which requires knowledge of your equipment, familiarity with your paint materials and experience. Differences in paints, work materials and environmental conditions make every painting task unique. For best results, practice with your painting mixture on a scrap pie

Chicago Electric MIG 200 93804

Scaricare : 3 File Size : 4 mb    Produttore : Chicago Electric  
Categoria : Saldatrici

© Copyright 2006 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. Contents PRODUCT SPECIFICATIONS................................................... 3 GENERAL SAFETY RULES ..................................................... 3 Specific Safety Rules ........................................

Chicago Electric SPOTLIGHT 30 MILLION CANDLEPOWER 93175

Scaricare : 85 File Size : 4 mb    Produttore : Chicago Electric  
Categoria : Altri strumenti

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 Specifications Specifications Power Source Light Bulb Lens Charging Adapters Weight Features Description Battery, sealed lead-acid, 12 VDC, 7 AH Xenon, 12 V, 35 W High Intensity Discharge (HID); 3000 hour life 9 inch (dia.) with reflector Power co

Chicago Electric 99702

Scaricare : 3 File Size : 3 mb    Produttore : Chicago Electric  
Categoria : Pistole

Turn the “PRIME/SPRAY” knob to the 16. “SPRAY” position and hold the Trigger down until all air and impurities are cleansed from the Hose and the paint runs pure. Release the Trigger. Turn the 17. “PRIME/SPRAY” knob to the “PRIME” position. Squeeze the Trigger once to make sure that pressure is released. Attach the Spray Tip: Turn the Sprayer off.18. Pull out and turn the key to lock the TriggerClose the gauge at the end of the tip to lock the gun 19. Lock the Gun and thread the Spray Tip on it.

Chicago Electric 95424

Scaricare : 1 File Size : 3 mb    Produttore : Chicago Electric  
Categoria : Saldatrici

® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. For technical questions, please call 1-800-444-

Chicago Electric 41903

Scaricare : 1 File Size : 3 mb    Produttore : Chicago Electric  
Categoria : Jig Saw e

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: ________

Chicago Electric 06271

Scaricare : 13 File Size : 3 mb    Produttore : Chicago Electric  
Categoria : Saldatrici

3. Insert the Handle (4) into the Handle Sockets (3) and mount the Handle Sockets to the Side Panel B (1) top using supplied hardware. Note: The Handle (4) configuration may differ slightly than what is shown in this manual. 4. Lift Side Panel B (1) all the way to expose the wire spool and Wire Feed Mechanism (11). Wire Feed Mechanism (11)Wire SpoolWire Spool Axle (10) Side Panel B (1) (C) (D) (34) – + 5. Remove the Nut from the Wire Spool Axle (10). Place the Wire Spool over the Axle with the w





categorie