Although the main lights operate immediately it will take a further 30 seconds before the fl ame eff ect starts. Press again to give fl ame effect and half heat. This will be indicated by two beeps. Press again to give fl ame effect and full heat. This will be indicated by three beeps. Press again to return to fl ame eff ect only. This will be indicated by one beep. Press to put stove in to standby mode. This will be indicated by one beep. Control Knob ‘C’:- Controls the intensity of the fl ame

2 Fig. 3 300 606 300 399 707 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 GB .................................................................................................................................... 1 FR .................................................................................................................................... 6 PT ..............................................................................

Only pull out the drawer when its time to refi ll the water tank or change a lamp, otherwise it may lead to excess water in the sump and reduced fl ame eff ect. If this happens empty the water from the sump as instructed under ‘Maintenance’. 2. With the flame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long than when it is at maximum fl ame setting. 3. Do not tilt or move the stove while there is water in the tank or sump. 4. Make sure that

Alternative condensate discharge options have to be agreed with the manufacturer. Do not discharge the condensate directly into septic pits or cesspools as the evaporator is likely to be destroyed by the aggressive vapours generated there. 5 MOUNTING 6 6 MOUNTING 6.1 General The following connections need to be established on the heat pump: -supply/return lines of the heating system -condensate drain -control lead to the remote control -power supply 6.2 Heating-Side Connection The connections on

The heating mode can be preselected by placing switch (3) to the Heating ( ) position. The desired return temperature can be set using selector dial (4), the relevant call for heat is controlled by the potentiometer and lies within a range of min. 10 °C and max. 55 °C. If the preset temperature is reached, the heat pump switches off. Once the return temperature drops below the preset temperature by 4 Kelvin, the heat pump switches back on. In the event that the preset return temperature cannot b

power input to pump) Air inlet temperature in [°C] Coefficient of performance (incl. power input to pump) Air inlet temperature in [°C] Condenser Heating water flow rate in [m3/h] 0 0,5 1 1,5 2 2,5 3 20 APPENDIX: 12.3 SCHEMATICS 12.3.8 Cooling mode LA 12TR 0 5 10 15 20 25 30 10 15 20 25 30 35 40 45 50 18 8 0 1 2 3 4 5 6 7 10 15 20 25 30 35 40 45 50 18 8 0 1 2 3 4 5 6 7 10 15 20 25 30 35 40 45 50 18 8 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 Cooling capacity in [kW] Conditions: Water f

In this context, particular attention must be paid to the proper disposal of refrigerants and refrigeration oils. 10 APPENDIX 12 12 APPENDIX 12.1 DIMENSIONED DRAWING 12 12.2 EQUIPMENT DATA 13 12.3 SCHEMATICS 12.3.1 Heating mode LA 6MR 14 12.3.2 Cooling mode LA 6MR 15 12.3.3 Heating mode LA 8MR 16 12.3.4 Cooling mode LA 8MR 17 12.3.5 Heating mode LA 10MR 18 12.3.6 Cooling mode LA 10MR 19 12.3.7 Heating mode LA 12TR 20 12.3.8 Cooling mode LA 12TR 21 12.3.9 Heating mode LA 16TR 22 12.3.10 Cooling m

CAUTION! CAUTION! damage the surface. CAUTION! CAUTION! CAUTION! Do not open the unit unless all electrical circuits have been disconnected from the During transport, the heat pump must not be tilted more than 45° (in either direction). Heat pump and transport pallet are only connected by the packaging film. The air intake and discharge openings must neither be constricted nor Clockwise phase sequence (in the case of multiphase units) must be observed: Damage to the compressor may be incurred if

We trust this manual will give you all the answers to the questions that you might have regarding the products. Although every care was taken to ensure the content of this manual is correct we do not accept any liability for claims resulting directly or indirectly from the application of the information contained in this manual. This manual is written specifically for the Dimples Solar product range. Any information contained therein must not be applied generally to any other solar products. Sho