If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante informacion sobre seguridad concerniente al mantenimiento, uso, y operacion de este producto. Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio dano. Si usted no puede entender el contenido de este man

For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C). OPERATION ALL MODELS CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. 1. Plug warmer into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See SPECIFICATIONS for details. 2. Turn the Power Switch to the ON position. See Figures 6 & 7. 3. Turn the Temperature Control to the desi

If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet. WARNING To prevent any injury, discontinue use if power cord Figure 3. Plug Configurations NEMA 5-15P CEE 7/7 Schuko BS-1363 is frayed or worn. ELECTRICAL RATING CHART Model Voltage Hertz Watts Amps Plug Configuration Shipping Weight FDW-1-MN 100 120 60 60 1110 1128 11.1 9.4 NEMA 5-15P NEMA 5-15P 80 lbs. (36 kg) 80 lbs. (36 kg) 220 50/60 1118

Do not connect the heater directly to a boiler or furnace coil or any other uncontrolled temperature source, or the thermostat could be damaged causing the unit to overheat. Unit is not weatherproof. For safe and proper operation the unit must be located indoors where the ambient air temperature is constant and is a minimum of 70°F (21°C). CAUTIONS Hatco requires that two temperature/pressure gauges, Hatco part number 03.01.003.00, be installed to assure proper operation. Install one in the supp

FR2M-0604 HATCO LIMITED WARRANTY 1. PRODUCT WARRANTY Hatco warrants the products that it manufactures (the “Products”) to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’s written instructions or 18 months from the date of shipment from Hatco. Buyer must establish the product’s purchase date by returning Hatco’s Warranty Registration Card or by other mean

Dimensions - Remote Control Box (RMB) 21 Form No. GRM-0707 TROUBLESHOOTING GUIDE WARNING WARNING To avoid any injury or damage the strip heater To avoid any injury or damage to the strip heater must only be serviced by qualified personnel. turn the power OFF at the disconnect switch/circuit breaker and allow to cool before performing any maintenance. SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Unit is turned “ON” but there is no heat. No power to unit. Check circuit breaker and reset as necessary.

1 Form No. GRM-0707 IMPORTANT SAFETY INFORMATION CAUTIONS Standard and approved manufacturing oils will smoke up to 30 minutes during initial start-up. This is a temporary condition. To assure safe operation, operate unit without food product until smoke dissipates. Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. To prevent unit failure do not add a decorative soffit to hide a pass-through mounted Glo-Ray Strip Heater. Strip Heaters with in

(9 kg) Model GRAH-84•• Watts: 2050 Shipping Weight: 19 lbs. (9 kg) Voltage 120 208 240 100 200 220• 240• Voltage 120 208 240 100 200 220• 240• Amps 12.5 7.2 6.3 15.0 7.5 6.8 6.3 Amps 17.1 9.9 8.5 20.5 10.3 9.3 8.5 Model GRA-96• • Watts: 1725 Shipping Weight: 21 lbs. (10 kg) Model GRAH-96•• Watts: 2400 Shipping Weight: 21 lbs. (10 kg) Voltage 120 208 240 100 200 220• 240• Voltage 120 208 240 100 200 220• 240• Amps 14.4 8.3 7.2 17.3 8.6 7.8 7.2 Amps 18.3 11.5 10.0 24.0 12.0 10.9 10.0 Model GRA-108

Do not install dual stripheaters (GRA-XXD, GRAH-XXD, GRAL-XXD & GRAHL-XXD Series) above non-metallic surface. Install all non-dual strip heaters sothere is a minimum distance of 3" (76 mm) from a non-metallic wall or adjacent surface. To avoid any injury or damage to the unitwhen using chains for installation, the chains must have sufficient strength and be securely fastened, or the unit could becomeloose or fall. Do not place anything on top ofwarmers supported by chains. To avoid any injury or

If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante informacion sobre seguridad concerniente al mantenimiento, uso y operacion de este producto. Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio dano. Si usted no puede entender el contenido de este manua