Anote estos números en las líneas de abajo y guárdelos para su referencia en el futuro. Número de modelo ____________________ Tipo ___________ Número de serie _________ Número de parte 893885-007 NORMAS DE SEGURIDAD IMPORTANTES ADVERTENCIA: Cuando use herramientas neumáticas siempre debe seguir las precauciones básicas de seguridad para reducir el riesgo de herida personal, incluyendo lo siguiente: LEA Y SIGA TODAS LAS INSTRUCCIONES. Hay ciertas aplicaciones para las cuales esta herramie

14). CAUTION: times. Keep tool pointed away from yourself and others at all Always connect tool to air supply before loading fasteners. Do not load fasteners with trigger or safety depressed. Always wear Z87.1 approved safety glasses, and hearing protection when preparing or operating the tool. Never use a tool that leaks air or . needs repair. ■ ■ 2. Depress latch (B) Fig. 15, open feeder cover and swing open magazine cover (see Fig. 16). 3. Adjust nail support (C) Fig. 16, for desire

Do not use liquid lubricants on this tool. CLEAN AND INSPECT DAILY CAUTION: Remove fuel cell and purge tool before cleaning and inspection. Correct all problems before placing the tool back in use. EXTERIOR Wipe tool clean and inspect for wear or damage. If necessary, use a solution of warm water and dish washing detergent to wipe exterior of tool only. DO NOT SOAK tool with cleaning solution. Do not use solvents on tool, this can damage internal parts. Do not use oil or grease on this too

Make sure all screws and caps are securely tightened. 5. NEVER USE TOOL IF trigger or compression mechanism are inoperable, missing or damaged. Do not alter or remove trigger or other components. Make daily inspections for free movement of trigger and compression mechanism. Do not use tool if trigger can be pulled without tool being fully compressed. 6. DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a repla

Wear protective hair covering to contain long hair. 9. USE SAFETY GLASSES. Wear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area where power tools are being operated should also wear safety glasses and face or dust mask. 10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced imme

THEY MAY IGNITE. ALWAYS OPERATE THE COMPRESSOR IN A WELL VENTILATED I AWAY FROM SPRAY AREA. AN ADDITIONAL LENGTH OF HOSE MAY BE REQUIRED. SECURE LOCATION AWAY FROM COMPRESSOR. NEVER PLACE OBJECTS AGAINST OR ON TOP OF COMPRESSOR. OPERATE IN AN OPEN AREA AT LEAST ANY WALL OR OBSTRUCTION THAT WOULD RESTRICT THE FLOW OF FRESH AIR TO THE VENTILATION OPENINGS. RISK OF ELECTRIC SHOCK YOUR AIR COMPRESSOR IS POWERED BY ELECTRICITY. LIKE ANY OTHER ELECTRICALLY POWERED DEVICE, IF IT IS NOT NEVER O

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. _ Type___ Serial No._ Part No. 888970-799 IMPORTANT SAFETY INSTRUCTIONS When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongl

Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. The depth that a fastener is driven is controlled by the pressure of the air supply. The amount of pressure required will vary depending on the size of the fastener being used and the material being fastened. Experiment with the air pressure setting to determine the best pressure for th

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. __^_ Type ........................ Serial No._. ................................................. ...................................................................................................;..................... Part No. 883794-699 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to

It is wired for 120 volt operation. Instructions for converting the motor for 240 volt operation can be found on a label attached to the side of the motor, or as follows: bwmiwlI When converting the compressor for 240 volt operation, the three-pronged 120 volt cord plug must be replaced with a three-pronged 240 volt plug (purchase plug locally or order 892545 cord and plug assembly). GROUNDING INSTRUCTIONS The air compressor is equipped with a cord having a grounded wire with an appropriate g