After the initial cleaning process the glass should be cleaned two or three times during each operating season depending on the environment in the house. Clean the glass after the first two weeks of operation. • The use of any non-approved replacement glass will void all product warranties. • Care must be taken to avoid breakage of the glass. • Do not operate appliance with glass front removed, cracked or broken. • A replacement glass frame assembly (complete with gasket) is available through yo

FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE Installation and service must be performed by a qualified installer, service agency or the gas supplier. WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electric switch; • Do not use any phone in your building. • Immediately call your gas supplier from your neighbor’s p

The least clearance is required when both the stove and the wall have heat shields. Reducing a stove clearance may require a listed heat shield on the chimney connector as well, or a double-wall connector. Clearances may be reduced only by means approved by the regulatory authority and in accordance with the clearances listed in this manual. The charts and sample installations that follow list all the clearances required for the various installation configurations of Dutchwest Convection Heaters

• Inspect for and remove ash build-up behind the combustion package. This should be done in conjunction with annual cleaning of the chimney connector since this inspection is most conveniently done through the flue collar opening. Inspect the passages to either side of the combustion package (a mirror will be helpful) and vacuum away ash using a flexible vacu30002291 25 26 Dutchwest Non-Catalytic Convection Heater 30002291 um hose inserted into each passage. Care should be taken not to damage th

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one. Cleaning the Glass Maintenance ST806 Fig. 30 Door latch adjustment. Small Locking Nut Pawl Striker Screw Door Large Lock- ing Nut You will find that

Dutchwest noncat cover 5/04 Homeowner’s Installation and Operating Manual If this heater is not properly installed, operated, and maintained, a house fire may result. For safety, follow all installation, operation and maintenance directions. Contact local building officials about restrictions and installation inspection requirements in your area. SAFETY NOTICE Non-Catalytic Convection Heater Model 2478 Dutchwest Non-Catalytic Convection Heater The Dutchwest Model 2478 covered in this Owner’s Gui

This can be achieved by ensuring that the hearth is constructed and sized in accordance with the guidelines included in section 2 of approved document ‘J’. The size and clearances of the hearth are as follows: The constructed hearth should be constructed in accordance with the recommendations in document J, and should be of minimum width 840 mm and minimum depth 840 mm (if a free standing hearth b) above) or a minimum projection of 150 mm from the jamb (if a recessed hearth a) above). Costructio

Masonry forms an effective ‘heat sink’ - that is, it absorbs and holds heat for long periods of time. The large mass, however, may take a long time to become hot enough to sustain a strong draft. The larger the chimney (in total mass), the longer it will take to warm up. Cold masonry will actually cool exhaust gases enough to diminish draft strength. This problem Dutchwest Non-Catalytic Convection Heater is worse if the chimney is located outside the home or if the chimney flue has a cross-secti

Place the key on your work surface with the threaded holes facing up. 2. Place the column right assembly onto the key. (Fig. 4) 3. Place the column left assembly onto key. (Fig. 5) KT424 column right assy 9/03 Key Column Right Assembly KT424 Fig. 4 Place column right assembly onto key. KT425 column left assy 9/03 Key Column Left Assembly KT425 Fig. 5 Place column left assembly onto key. 4. Install the upper mounting bracket. Use the upper mounting without the marked “R” stamped on the face. (Fig

Montpelier Wood Insert NOTE: Cast iron parts can be heavy, an assistant would be advisable. CAUTION: Porcelain enamel is fragile. The finish can be easily damaged if castings are not handled carefully. Always place castings on a protective surface, such as a towel, blanket or carpet. Table of Contents Traditional Cast Surround Models: MEAD3CB, MEAD3EB, MEAD3BS...................................................................2 Small Cast Profile Surround Models: CAPCB, CAPEB ....................