Discard the fuel tank and the rubber grommets. 5. Cut the tie wraps that fasten the fuel supply hose to the frame rail. 6. Cut 10” (25,4cm) from the fuel supply hose and wire loom covering. Route on the inside of the frame rail. INSTALLATION 1. Install the iso mounts in the front inserts of the new tank. 2. Install the new tank mount bracket onto the existing tank mount plate and secure with the supplied hardware. See Figure 1 below for mount and hardware orientation. Make sure to use to ho
Save the hardware. 2. Remove the cross bar and mounts from the fuel tanks. Save the hardware. 3. Remove the fuel supply hose from the bottom of the fuel tank and drain all remaining fuel into a suitable container. Awarning Gasoline is highly flammable and must be handled with care. Do not allow open flame, smoking or matches in the area. 4. Remove the fuel tank from the machine and save all of the hardware. Discard the fuel tank and the rubber grommets. 5. Cut the tie wraps that fasten the
Secure the fuel supply hose to the frame rail, making sure not to contact the pump cooling fan. 5. Reinstall the cross bar and mounts onto the new tank and secure with the saved hardware. 6. Reinstall the bumper and secure with the saved hardware. A. 3/8” x 1-1/4” Bolts E. B. 3/8” SAE Washers F. C. Tank Mount Bracket G. D. Tank Mount Plate H. 3/8” Fender Washers 3/8” Nylon Lock Nuts 5/16” x 1-1/4” Bolts 5/16” SAE Washers © Copyright 2003 Ferris Industries. All Rights Reserved. 1 48714
48550 For Derby Pacer 1334 Kit Contents: Ref Part No. Qty. Description A. 1724832 1 MULCH PLATE B. 1724457 1 34” BAFFLE C. 1923362 1 NUT, Hex Lock, 5/16-18 D. 1679163 1 WING NUT E. 1724475 1 J-BOLT F. 25127 5 NUT, Serrated Flange, 5/16-18 G. 1931333 5 CARRIAGE BOLT, 5/16-18 3/4 O ii /• i ~ A fr "'n -V t'r"} y / Figure 1. Kit Components © Copyright 2003 Ferris Industries. All Rights Reserved. 1 48551 Rev. 01/2003 TP 200-7115-00-SK-D Installation Instructions 34” Mulching
This kit should be installed when using the Triple Bagger Grass Collection System. Kit Contents: Ref Part No. Qty. Description 1 22467 2 Oil Cooler 2 1846152 1 Mount Bracket-Left 3 1846153 1 Mount Bracket-Right 4 1846154 1 Oil Cooler Mount 5 22106 2 3/8” Hose Fitting 6 21164 4 Hose Clamp 7 25299 8 Bolt, 1/4-20 x 3/4” Torx Head 8 25095 8 Nut, 1/4-20 Nylon Lock 9 50860-19 1 3/8” Hose, 19” (not shown) 10 50860-25 1 3/8” Hose, 25” (not shown) 11 50860-48 2 3/8” Hose, 48” (not shown) 12 50862-18 1 3/
See Figure 4 for the proper hose locations. Secure with the enclosed hose clamps. 18. Install the tie wraps as shown in Figures 4-6. Use a long tie wrap to secure the 48” hoses to the 5/8” supply hose. Position the hoses so the do not contact the battery pan. Use the remaining two long tie wraps the bundle the hoses together in front of the engine. Be sure the tie wrap the hoses to the engine screen. Use the short tie wrap to secure the 25” hose to the engine oil dipstick tube. Do not overtighte
1846261 © Copyright 2000 Ferris Industries. All Rights Reserved. 1 Rev. 9/2000 TP 200-7030-00-SL-D Figure 1. Kit Contents 1 4 32 8 7 6 5 Figure 2. Fitting Orientation Installation Instructions 1846197 7. Block the front wheels and jack up the rear of the machine and set on jack stands or wooden blocks. Remove the left drive tire. This will allow for easier access to the left hand pump. 8. Remove the left return hose and loosen the jam nut on the fitting on the pump. Rotate the fitting towards th
Residual dirt and grass is easily removed immediately after mowing. 1. Remove grass deposits with a brush and a cloth. 2. Oil the red cutting mechanism lightly with thin oil (e.g. sprayed oil). 7. Troubleshooting DANGER! Cutting tool can cause injuries! V Wear suitable work gloves when rectifying faults. 10 Fault Possible Cause Rectification Abnormal Noises Screws / components loose v Tighten screws Foreign bodies on the blade. v Remove foreign bodies. Notch in the blade v Remove notches with gr