Log:
Ordina : Nome ↑   Scaricare   Valutazione   Size ↑  

Ferris Industries 1000ZK21/48

Scaricare : 24 File Size : 2 mb    Produttore : Ferris Industries  
Categoria : falciatrici

Drain crankcase oil while engine is hot and refill with a grade of oil that will be required when unit is used again. 2. Prepare the mower deck for storage as follows: a. mower deck from the unit. b. Clean underside of mower deck. c. Coat all bare metal surfaces with paint or light coat of oil to prevent rusting. 3. Clean external surfaces and engine. 4. Prepare engine for storage. See engine owner’s manual. 5. Clean any dirt or grass from cylinder head cooling fins, engine housing and air clean

Ferris Industries ES 500

Scaricare : 20 File Size : 547 kb    Produttore : Ferris Industries  
Categoria : falciatrici

2. Keep safety interlock B pressed down and pull starting lever C on the upper handle 3. The Lawn Scarifier starts. 3. Release safety interlock B. When in operation, the extension cable 0 must always be guided in the direction you are working and to the side of the area to be worked on. Always work away from the connection cable. 14 Blockage Protection: If the aerator cylinder is blocked, e.g. by a foreign body, immediately release the starting lever. If the blockage lasts longer than 10 seconds

Ferris Industries 5900606

Scaricare : 16 File Size : 4 mb    Produttore : Ferris Industries  
Categoria : falciatrici

Place the adjustment pin in the desired cutting height and release the lift lock lever. Throttle Control The throttle controls engine speed. Move the throttle forward to increase engine speed and back to decrease engine speed. Always operate at FULL throttle. Choke Close the choke for cold starting. Open the choke once the engine starts. A warm engine may not require choking. Pull the knob UP to close the choke. Push to knob DOWN to open the choke. Hour Meter / Maintenance Reminder Measures the

Ferris Industries RM 380

Scaricare : 12 File Size : 271 kb    Produttore : Ferris Industries  
Categoria : falciatrici

keit erst nach mehreren Lade- A Vor dem Einstellen oder Saubern ist der Motor- Ist der Accu vollig entladen, maher auszuschalten und z. B. durch lang andauernde gegen unbeabsichtigtes Ein- Lagerung ohne zwischenzeitschalten zu schutzen. Dazu ist liche Nachladung, dann ist der Schlusselschalter Q aus die volle Accu-Kapazitat erst der Kontaktbuchse des Motor- nach mehreren Lade- / Entlademahers zu ziehen. vorgangen wieder verfugbar. 7.2 Der Accu (Abb. E/ G) Laden des Accus temperatur oder Aufheizu

Ferris Industries 380

Scaricare : 7 File Size : 114 kb    Produttore : Ferris Industries  
Categoria : falciatrici

Residual dirt and grass is easily removed immediately after mowing. 1. Remove grass deposits with a brush and a cloth. 2. Oil the red cutting mechanism lightly with thin oil (e.g. sprayed oil). 7. Troubleshooting DANGER! Cutting tool can cause injuries! V Wear suitable work gloves when rectifying faults. 10 Fault Possible Cause Rectification Abnormal Noises Screws / components loose v Tighten screws Foreign bodies on the blade. v Remove foreign bodies. Notch in the blade v Remove notches with gr

Ferris Industries 1000z Series

Scaricare : 6 File Size : 913 kb    Produttore : Ferris Industries  
Categoria : falciatrici

Store in a dry area. Hang the catcher and catcher bags to dry thoroughly before storing for a long period of time. Always store away from moisture. MOWING WITHOUT THE BLOWER For operation without the blower, the deflector must be properly installed in the down position and retained by the spring latch (Derby models only). To remove the blower, reverse the installation steps. 3 Initial Installation & Assembly 48” & 52” DOUBLE-BAG COLLECTION SYSTEM BLOWER MOUNT & DRIVE GROUP Remove Discharge Chute

Ferris Industries 5900626

Scaricare : 5 File Size : 4 mb    Produttore : Ferris Industries  
Categoria : falciatrici

Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders. CHECKS BEFORE STARTING • Check that crankcase is filled to full mark on dipstick. See the engine Operators Manual for instructions and oil recommendations. • Check the radiator fluid level. See engine operator’s manual for instructions. • Check the

Ferris Industries 5900607

Scaricare : 4 File Size : 4 mb    Produttore : Ferris Industries  
Categoria : falciatrici

Stationary Idler Pulley 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. 2. Lower the mower deck to its lowest cutting position and remove the mower deck guards. 3. Using a 1/2” breaker bar, place the square end in the square hole located in the end of the idler arm (A, Figures 41). Carefully rotate the breaker bar clockwise, which will relieve the tension on the belt exerted fr

Ferris Industries 300

Scaricare : 3 File Size : 114 kb    Produttore : Ferris Industries  
Categoria : falciatrici

9 GB Adjusting the cutting height: 566 The cutting height can be set to any position between 12 mm and 42 mm. 1. Stand behind the cylinder mower with one foot on the roller 5. 2. Release the two locking screws 6 and adjust to the correct height in the inspection window 7. 7 3. Tighten the two locking screws 6 on both sides to the same height. The locking screws 6 must always be set to the same height on both sides. The mower may only be adjusted to a depth in which the lower blade does not touch

Ferris Industries 5901181

Scaricare : 2 File Size : 4 mb    Produttore : Ferris Industries  
Categoria : falciatrici

Actual gross engine power may be lower and is affected by, but not limited to, ambient operating conditions and engine to engine variability. Given both the wide array of products on which engines are placed, and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net horsepower). This difference is due to a variety of factors including, but not limited





categorie