Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator. IMPORTANT: For more detailed maintenance and adjustment information refer to the proper parts manual for your machine. The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property. The owner should also ensure that the operator/mechanic know that they are responsible for their own safety as well as the safety

Do not operate the mower without either the discharge chute or the entire grass collection system in place. Fig. 3-12 600876_0706 15 600876_0706 Mower deck operation DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly. With the engine running, engage the deck clutch switch (Fig. 3-1) and advance engine thr

C. Deck clutch switch (Fig. 3-1) — this switch engages the deck. Pull the switch up to engage and push switch down to disengage the clutch. IMPORTANT: Never engage clutch with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged. D. Ignition switch (Fig. 3-1) – a three position switch: off, run, and start. With key inserted, rotate it clockwise to START position; release key when engine starts, and switch will automatically return to the RUN position.

A separate Engine Manual is included with your owner’s packet which contains additional engine information that will not be repeated in this manual. You are urged to read it before attempting any operation or repair of the engine. The Quick Reference Decals are designed to give the operator brief information needed in the daily operation of the machine. These decals are not intended to be used in place of this manual but instead are to be used as an extension of this manual. These decals should

An operator should not operate on a slope until he is thoroughly familiar with the equipment. Do not operate on slopes greater than 15 degrees. Refer to Figure 2-1, page 7, when determining the degree of slope to be mowed. IMPORTANT: The Hustler ATZ only, is capable of operating on slopes of 15 degrees or more (maximum 25 degrees). Do not operate the Hustler ATZ on slopes greater than 25 degrees. Refer to Figure 2-1, page 7 when determining the degree of slope to be mowed. It is strongly recomme

• Always maintain a safe distance from people and petswhen mowing. • Always stop machine if some- one enters the area. • Disconnect spark plug before servicing WARNING: Falling! • Before and while backing, look behind and down for small children and obsticles.• Go across slopes, not upand down 3-2 108548_0711 OPERATION Safe Operating Practices This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death. Operati

4-13 Refer to Fig. 4-12 SERVICE AT INTERVALS INDICATED WEEKLY OR 50 HOURS ANNUALLY OR 100 HOURS Verify safety start interlock system Prior to each use Visually inspect unit for loose hardware and/or damaged parts Prior to each use Visually inspect tires Prior to each use Check oil level, engine (1) Prior to each use or every 4 hours Clean air intake screen (4) Prior to each use or every 4 hours Clean foam element (4) Prior to each use or every 4 hours Check fuel level Prior to each use Blades -

Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Use soda mixed in water to clean corrosion off the terminals. Avoid crushing Do not jump if machine tips Use seat belt Seat belt must be fastened while operating this machine. Failure to use seat belt will result in serious injury in the event of a roll over. Keep engine and pump compart-ment(s) clean (espec

WARNING: Always lower the hydraulic lift and equipment before stopping the unit. ight transfer valve The weight transfer valve is used to transfer the front ent weight to the tractor unit to reduce equipment on turf and prevent damage and improve front drive eel traction. Figure 3-11 The weight transfer valve should be used according to the ng procedures; With the engine running, push the hydraulic lift lever forward to the floating position. Turn the adjusting knob clockwise until the mower or

Change more often under dusty or dirty conditions and during hot weather periods. 2. Torque initially and after first 2 hours of operation. 3. Perform initial hydraulic filter change after 50 hours (one week) of operation. 4. Change engine oil filter per the engine manufacturer’s recommendations. Refer to Engine Owner’s Manual for recommendations and other maintenance items. 5. Service more often under dusty or dirty conditions. Use caution when servicing to prevent dust contamination in the eng