When installing a K00365 on a Manitowoc dispenser, remove the gray side trim pieces on the top sides of the dispenser. B. Place support angle on bin or dispenser, as shown, prior to adapter installation. Locate foam tape from kit in the positions on top of bin, as shown. Note locations of narrow and wide tape. C. Place adapters on bin or dispenser, as shown. Make sure the two holes from the support angle and adapters are aligned on the side. D. Using the adapters as templates, drill three 5/3
Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Web Site - Rev. 8016483 02/03/05
Deburr suction line before fitting new tubing in. 11. Braze all tubing into place. Purge system with nitrogen during all brazing operations on the ice machine. NOTE: IF REPLACING COMPRESSOR INTO A REMOTE ICE MACHINE, MAKE SURE TO FIRST FOLLOW INSTRUCTIONS A, B, AND C BELOW, BEFORE PROCEEDING TO INSTRUCTION #10. A. Replace elbow with “T” fitting. 12. Use electrical tape to seal suction line insulation. B. Replace HPR valve and L-shaped tube that was removed earlier. Adjust to fit without ru
C836-72-1 . C0836-72 . C0836-72-1 . C0836-72M . C0836-72-1M Standard Features: • Griddle top with 1" (25mm) thick steel plate. • Full-range valve control (-72) • Griddle control, with embedded thermostat sensor bulb Low to 500F (260C) (-72-1) • Stainless front and sides • Stainless steel front rail w/ position adjustable bar • 1 1/4" NPT front gas manifold • Can be connected individually or in a battery • 6" (152mm) high stainless steel stub back • 6"(152mm) chrome steel adj. legs Model C836-72-
Tighten 1/2” conduit nut to conduit fitting. 7. Screw start component electrical box to refrigeration platform close to compressor. 8. Wire-nut L1 (black) wire lead to wire lead #78 and L2 (white) wire lead to wire lead #77. 9. Break out bottom knockout of compressor electrical box and attach common, run, and start wire leads to compressor terminals, per new wiring diagram. 10. Peel backing off new wiring diagram and place over existing wiring diagram. Manitowoc Ice, Inc. 2110 South 26 Str
CAUTION! Remove entire system charge before proceeding. a. Remove the insulation from the suction line liquid heat exchanger assembly. You will see the liquid line soldered to the suction line for approximately 15”. You must remove this soldered length. b. Remove the liquid line from the suction line. Starting at the evaporator end, use a pliers and a low flame torch to carefully separate the liquid line from the suction line. c. Reinsulate the suction line. Run the removed liquid line outsid
Install extra washer under existing washer (see Illustration, Sheet 2). 4. Use procedure "A" or "B": A. Recover refrigerant. When work is complete, weigh in new refrigerant. -ORB. Pump down to 2 lb. and close receiver valve. a. Using pinch-off tool, pinch off 1/4" line to cap tubes (see Illustration, Sheet 2). NOTE: Pinch-off is required because the refrigerant is isolated from the low side between receiver valve and hot gas solenoid. b. Cut top of 1/4" stub off. c. Route new low-pressure
A. Verify valve and schrader caps are tightened to specifications (see Step 6). PRE-FORMED INSULATION TIGHTEN VALVE CAPS TO SPECIFICATIONS SV3084 B. Place insulation over schrader valve cap and left side of valve. Position the tab between the mounting bracket and rear panel. SV3085 PLACE TAB BETWEEN VALVE BODY AND PANEL C. Fold insulation and hold against right hand side of valve while securing with electrical tape. Seal the line set insulation to the shut off valve insulation with electrical ta
Let the RTV sealer dry for approximately one hour. 8. Install water trough, float valve, water pump, water distribution tube assembly, water curtain, and front support angle. When installing the water trough, you may have to slot the mounting holes on the ends of the water trough to allow for the thickness of the cycolac panel on the bulkhead rear. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/
Position splash shield into water trough so that all the water is deflected back into the trough. 3. Tighten evaporator mounting screws. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8009883 Rev. 08/25/97