Log:
Ordina : Nome ↑   Scaricare   Valutazione   Size ↑  

Manitowoc Ice J-0600

Scaricare : 13 File Size : 121 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

Deburr suction line before fitting new tubing in. 11. Braze all tubing into place. Purge system with nitrogen during all brazing operations on the ice machine. NOTE: IF REPLACING COMPRESSOR INTO A REMOTE ICE MACHINE, MAKE SURE TO FIRST FOLLOW INSTRUCTIONS A, B, AND C BELOW, BEFORE PROCEEDING TO INSTRUCTION #10. A. Replace elbow with “T” fitting. 12. Use electrical tape to seal suction line insulation. B. Replace HPR valve and L-shaped tube that was removed earlier. Adjust to fit without ru

Manitowoc Ice 1480279

Scaricare : 10 File Size : 14 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

This pump will fit most Manitowoc ice machines. The discharge port located on the base of the water pump can be rotated, if necessary, for proper positioning in the ice machine. If it is required to rotate the water pump, remove the three machine screws from the pump, turn the base to the desired position, and reinsert the screws. The positioning holes are spaced every 60° in the water pump. When installing this water pump, remove the water flow clamp from all ice machines except the regular c

Manitowoc Ice Q-0420

Scaricare : 10 File Size : 120 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

4. Pull evaporator away from bulkhead. Place bottom of mylar strip in sump trough and slip up behind evaporator (align slot cut in step 3 with bin switch wire). Mylar must extend above bottom evaporator mounting screw (approximately 2” above gasket/bulkhead joint). 5. Remove paper backing from mylar. Apply tension to mylar to eliminate wrinkles. 6. Align evaporator extrusion and bulkhead screw holes; puncture mylar for the bottom screw holes and insert screws. Install all remaining evaporator sc

Manitowoc Ice FS1

Scaricare : 8 File Size : 13 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

CAUTION! Remove entire system charge before proceeding. a. Remove the insulation from the suction line liquid heat exchanger assembly. You will see the liquid line soldered to the suction line for approximately 15”. You must remove this soldered length. b. Remove the liquid line from the suction line. Starting at the evaporator end, use a pliers and a low flame torch to carefully separate the liquid line from the suction line. c. Reinsulate the suction line. Run the removed liquid line outsid

Manitowoc Ice J-1300

Scaricare : 7 File Size : 12 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

For ease of installation, position compressor on mounting bolt so that the suction port is to the rear of the ice machine. Note: Reducer bushings are provided for suction and process ports. Manitowoc Ice, Inc. 2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8011053 Web Site - Rev. 06/19/03

Manitowoc Ice CA200

Scaricare : 7 File Size : 23 kb    Produttore : Manitowoc Ice  
Categoria : Altri elettrodomestici da cucina

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Web Site - 8010213 Rev. 08/20/03 1

Manitowoc Ice CA260

Scaricare : 6 File Size : 23 kb    Produttore : Manitowoc Ice  
Categoria : Altri elettrodomestici da cucina

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Web Site - 8010213 Rev. 08/20/03 1

Manitowoc Ice C0836-72

Scaricare : 6 File Size : 222 kb    Produttore : Manitowoc Ice  
Categoria : Altri elettrodomestici da cucina

C836-72-1 . C0836-72 . C0836-72-1 . C0836-72M . C0836-72-1M Standard Features: • Griddle top with 1" (25mm) thick steel plate. • Full-range valve control (-72) • Griddle control, with embedded thermostat sensor bulb Low to 500F (260C) (-72-1) • Stainless front and sides • Stainless steel front rail w/ position adjustable bar • 1 1/4" NPT front gas manifold • Can be connected individually or in a battery • 6" (152mm) high stainless steel stub back • 6"(152mm) chrome steel adj. legs Model C836-72-

Manitowoc Ice Q-0320

Scaricare : 6 File Size : 120 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

Preparation 1. Disconnect power from ice machine. 2. Remove front, top, and side panels. 3. Drain water from sump trough. 4. Ice machine must be thoroughly dried before the insulation can be installed. Use towels to dry bulkhead and base assembly. Base Insulation Installation 1. Raise the ice machine above the bin. A high lift can be used, or (two people required) lift front edge of ice machine and place wood blocks (2”x 4”) between ice machine and bin. Lifting one side of ice machine at a time,

Manitowoc Ice FS2

Scaricare : 6 File Size : 13 kb    Produttore : Manitowoc Ice  
Categoria : attrezzature di pompaggio

Tighten 1/2” conduit nut to conduit fitting. 7. Screw start component electrical box to refrigeration platform close to compressor. 8. Wire-nut L1 (black) wire lead to wire lead #78 and L2 (white) wire lead to wire lead #77. 9. Break out bottom knockout of compressor electrical box and attach common, run, and start wire leads to compressor terminals, per new wiring diagram. 10. Peel backing off new wiring diagram and place over existing wiring diagram. Manitowoc Ice, Inc. 2110 South 26 Str





categorie