Follow the instructions on the battery charger. SERVICE NOTE: Make sure you plug the battery charger into the connector with the handle attached to it. IMPORTANT: Make sure you have an appropriate charger for use on Gel cell batteries. Use only “voltage-regulated” or “voltage-limited” chargers. Standard constant current or taper current chargers MUST NOT be used. A temperature-sensing charger is recommended, as manual adjustments are never accurate and will damage any VRLA battery. B-18 - FORM
17 FUSE BOARD ................................................................................................................................................. 17 RELAY BOARD .............................................................................................................................................. 17 WIRING DIAGRAM ......................................................................................................................................... 17 HYDRAULIC DIAGRAM .....
to persons are marked with this danger symbol. tips and instructions which structions to This indicates instructions these operating in- english Symbols used to mark Safety instructions in Before using the high-pressure This symbol is used cleaner, be sure to mark safety into also read the structions that must enclosed operat-be observed to preing instructions and vent damage to the ma- keep them within reach at all chine and its performance. times. 1 Important safety instructions For your own s
Edificio Central Park Herrera 1855, Office 604 Ciudad Autonoma de Buenos Aires Tel.: (+54) 11 6091 1571 AUSTRALIA Nilfi sk-Advance 48 Egerton St. P.O. Box 6046 Silverwater, N.S.W. 2128 Tel.: +61 2 8748 5900 E-mail: info@nilfisk-advance.com.au AUSTRIA Nilfi sk-Advance GmbH Metzgerstrasse 68 5101 Bergheim bei Salzburg Tel.: 0662 456 400-14 E-mail: info.at@nilfisk-advance.com BELGIUM Nilfi sk-Advance n.v-s.a. Riverside Business Park Boulevard Internationalelaan 55 Batiment C3/C4 Gebouw Bruxelles 10
Raise the squeegee tool off the floor, then unsnap the Center Latch (A) on the squeegee tool. 2 Remove the Tension Straps (B). 3 Slip the rear blade off the alignment pins. 4 The squeegee blade has 4 working edges. Turn the blade so a clean, undamaged edge points toward the front of the machine. Replace the blade if all 4 edges are nicked, torn or worn to a large radius. 5 Install the blade, following the steps in reverse order and adjust the squeegee tilt. To Reverse or Replace the Front S
Nilfisk C 120.3 Nilfisk C 125.3 Nilfisk C 120.5 X-TRA User Manual 128330335 Printed in China Copyright © 2010 Nilfisk, Division of Nilfisk-Advance A/S Index 1 Safety precautions and warnings .............................................3 2 Description ...............................................................................5 3 Before you start using your pressure washer ...........................6 4 Operating your pressure washer ..............................................7 5 Fields of
NOTE (Non AXP/EDS Models): For a consistent reduced flow of solution; open the Solution Flow Control Valve Lever (7) all the way and then turn ON the Smart Solutions™ / ECO Solution™ Valve (26). When the lever is in the “OFF” position; the machine operates conventionally; solution fl ow is determined by the Solution Flow Control Lever (7). When the lever is in the “ON” position; solution flow is controlled automatically. The Solution Flow Control Lever (7) should not be shut off, but is otherwis
The machine will restart after a few minutes when the thermal sensor has cooled. 4 2 Description 2.1 Application 2.2 Operation elements and model survey This high-pressure washer has been developed for domestic use within: - Car, motorbike, boat, caravan, trailer, patio/drive/flagstones, woodwork, brickwork, barbecue, garden furniture, lawn mower See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet with filter (2a) 3 High pressure connection 4 High pressure hose 5 Electr
Vary the pressure on the Drive Paddle (34) to obtain the desired speed. NOTE: Speed Control Knob (35) is used to control the maximum speed in either forward or reverse. 4 Press and hold the Solution Switch (B) for 5 seconds to pre-wet the floor. NOTE: This must be done prior to pressing the Scrub ON Switch (I). 5 Press the Scrub ON Switch (I) once for Regular Scrub or twice for Heavy Scrub mode. Hold this switch for 5 seconds for Extreme Scrub mode. Both the solution system and detergent (EDS