Log:
Ordina : Nome ↑   Scaricare   Valutazione   Size ↑  

Genie GS-2668 DC

Scaricare : 51 File Size : 925 kb    Produttore : Genie  
Categoria : Attrezzature per TC

82750 Third Edition • Third Printing Operator's Manual SAFETY RULES Do not alter or disable the limit switches. Do not drive over 0.5 mph / 0.8 km/h with the platform raised. Do not depend on the tilt alarm as a level indicator. The tilt alarm sounds on the chassis and in the platform when the machine is on a severe slope. If the tilt alarm sounds: Lower the platform. Move the machine to a firm, level surface. If the tilt alarm sounds when the platform is raised, use extreme caution to lower the

Genie GS-2632

Scaricare : 42 File Size : 886 kb    Produttore : Genie  
Categoria : Sedie a rotelle

Genie GS-2032 and Genie GS-2632 Part No. 82784 Second Edition • Second Printing Operator's Manual Component Damage Hazard Do not use the machine as a ground for welding. Explosion and Fire Hazard Do not operate the machine in hazardous locations or locations where potentially flammable or explosive gases or particles may be present. Damaged Machine Hazards Do not use a damaged or malfunctioning machine. Conduct a thorough pre-operation inspection of the machine and test all functions before each

Genie TZ-50

Scaricare : 33 File Size : 2 mb    Produttore : Genie  
Categoria : Altri dispositivi personali

Charging the Batteries with the AC Charger 1 Be sure the engine (if equipped) is turned off. 2 Be sure the batteries are connected before charging the batteries. 3 Open the machine covers. The covers should remain open for the entire charging cycle. 4 Remove the battery vent caps and check the battery acid level. If necessary, add only enough distilled water to cover the plates. Do not overfill prior to the charge cycle. 5 Replace the battery vent caps. 6 Connect the battery charger to a grounde

Genie TMZ-34/19

Scaricare : 33 File Size : 513 kb    Produttore : Genie  
Categoria : Attrezzature per TC

Component damage may also result if problems are not discovered and repaired in a timely fasion. 1 Check the tire surface and sidewalls for cuts, cracks, punctures and uneven or excessive tread wear. Result: Replace the tire if uneven or excessive tread wear is found. Always replace the tire with specifications equal to original equipment manufacturer. 2 Check each wheel for damage, bends and cracks. Result: Replace the wheel if any damage is found. 3 Check each tire with an air pressure gauge a

Genie MOBILITY AID GS-3384

Scaricare : 28 File Size : 641 kb    Produttore : Genie  
Categoria : Sedie a rotelle

If the light stays red, tag and remove the machine from service. OPERATING INSTRUCTIONS Indicator Light Flashing Red If the indicator light is flashing red, the platform is overloaded and no functions will operate. An alarm will sound at the platform controls. Remove weight from the platform. Push in and pull out the red Emergency Stop button to reset the system. If the platform is still overloaded, the light will continue to flash. To Extend and Retract Platform 1 Lift the platform extension lo

Genie 43650

Scaricare : 27 File Size : 1 mb    Produttore : Genie  
Categoria : Attrezzature per TC

Result: The machine should move in the direction that the blue arrow points on the drive chassis, then come to an abrupt stop. 48 Slowly move the drive control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the yellow arrow points on the drive chassis, then come to an abrupt stop. Note: The drive brakes must be able to hold the machine

Genie TMZ-50/30

Scaricare : 27 File Size : 3 kb    Produttore : Genie  
Categoria : Attrezzature per TC

Genie GTH-1048

Scaricare : 25 File Size : 4 mb    Produttore : Genie  
Categoria : Attrezzature per TC

114101 TABLE OF CONTENTS TABLE OF CONTENTS SECTION 1 ROUGH TERRAIN FORK LIFT SAFETY SECTION 1-1 Introduction 1-3 Standards And Symbols 1-4 Safety 1-5 Training And Knowledge 1-5 Operator's Responsibilities 1-6 Management's Responsibilities 1-7 Maintenance And Repair 1-8 Operation Safety 1-9 SECTION 2 GENERAL SAFETY 2-1 General Safety Procedures 2-3 Jump Starting 2-8 Proper Load Chart Use 2-9 SECTION 3 CONTROLS AND INSTRUMENTS 3-1 Operator's Compartment 3-3 Joystick Control Functions 3-4 Joystick

Genie AWP 114002

Scaricare : 22 File Size : 884 kb    Produttore : Genie  
Categoria : Attrezzature per TC

114002 Third Edition Fourth Printing Part No. 114002 Operator’s Manual Third Edition • Fourth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall be permitted to operate this machine. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Contents Page Safety Rules ..........

Genie TZ-50 TZ-50

Scaricare : 22 File Size : 876 kb    Produttore : Genie  
Categoria : Altri dispositivi personali

82900 with Maintenance Information Operator's Manual First Edition • Sixth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall be permitted to operate this machine. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Contents Page Safety ...................................





categorie