When the printer is used as a kitchen printer, please use this port for kitchen bell connection instead. Power Connection The power connector is a 3-PIN jack between the peripheral connector and the parallel connector for PP-8000. Either a Posiflex supplied power adaptor or a printer power cable from a Posiflex POS system can be connected to this connector to supply power for this printer. During insertion of the power plug, be sure to hear the click to obtain a firm contact. CAUTION: Before doi

: C NOTICE The manufacturer of the POS cash drawer makes no representation or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect, special or consequential damages. Information in this document is subject to change without notice and does not represent a commitment on the part of the manufacturer. FCC NOTICE This equipment generates, uses, and can radiate

A0 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to EN55022 and 47 CFR, Part 2 and subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this

For CR4004/ 4104/ 4214: Power connector cable and I/O bracket plate. INSTALLATION CR4000 / 4100 / 4210 Connect the drawer to POS system/printer as shown below: CR4001 / 4101 / 4211 CASH DRAWER With Printer Interface 8P Telephone Jack 8P Telephone Plug 6P Telephone Plug Output to drawer POS System or Printer Ground Rear View Control signal input 1). Connect the drawer serial I/P port to the computer COM port. Connect the power adapter output to the Power Input jack 2). No other RS232C devices sho

This utility can assign to each LAN printer a different device name for easy recognition. In case of confusion, please check the MAC addresses listed in this utility against the MAC address label you can find under each printer. Printer Driver Setup Any PC connected in same network can use TCP/IP to use PP-8000L in the way like a directly connected local printer. So, for direct I/O control by tools like “HyperTerminal” all commands applicable to the serial or parallel interface model can work on

Apply some mechanical assistance in below procedures to help resetting the cutter blade back to its home position. Please lift up a transparent protective cover over the adjustment wheel with the printer powered off. Turn this wheel downward for 4 or 5 strokes. Close the cutter cover back and turn the printer power on to see if the auto cutter lock up problem is resolved. If the problem is not automatically resolved by above procedures, please power off the printer and open the cutter cover agai

2.If the cash drawer is connected to a Posiflex POS system, follow the technical instruction of the system to open the cash drawer. CR-4001 / 4101 / 4211 / 4002 / 4102 / 4212 / 4004 / 4104 / 4214 1.Under DOS prompt, type “MODE COM1 96 N 8 1”. Hit the ENTER key. 2.Type “TYPE CON>COM1”. Hit the ENTER key. 3.Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER key, then the drawer will open. 4.Hit CTRL-C (Press Ctrl and C keys together) to return the computer back to the normal display mod

FUNCTIONAL TEST CR4000 / 4100 / 4210 1.Follow the printer’s manual of the printer the cash drawer is connected to open cash drawer. 2.If the cash drawer is connected to a Posiflex POS system, follow the technical instruction of the system to open the cash drawer. CR-4001 / 4101 / 4211 / 4002 / 4102 / 4212 / 4004 / 4104 / 4214 1.Under DOS prompt, type “MODE COM1 96 N 8 1”. Hit the ENTER key. 2.Type “TYPE CON>COM1”. Hit the ENTER key. 3.Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER

Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference. Warranty Limits: Warranty terminates automatically when any person other than the authorized technicians opens the machine. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 1 MODEL NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 2 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2 OPTIONS . . .