Worn water seals, abrasives in water, or natural 3. Check filter. Replace water seals. See service center wear 4. Clean inlet and discharge valve assemblies. Check 4. Fouled or dirty inlet or discharge valves filter 5. Restricted inlet 5. Check garden hose, may be collapsed or kinked. Check inlet water flow 6. Worn inlet or discharge valves 6. Replace worn valves 7. Leaking high pressure hose 7. Replace high pressure hose 8. Pump drawing in air 8. Ensure hoses and fittings are tight 9. Unloader

Use 10W-30 automotive detergent oil. See your Honda Owner’s manual for specific information. • Change oil if operating under heavy load or high ambient temperature. • Clean or replace paper air cleaner cartridge. Tap gently to remove dirt. • Change oil. • Replace spark plug. • Replace paper air cleaner cartridge. • Change engine oil. Maintenance Schedule Action needed Engine Oil Type Engine Oil Capacity Honda GX160 Honda GX270 Honda GX390 Engine Fuel Capacity Honda GX160 Honda GX270 Honda GX390

for use when contacting the manufacturer: Model No. ______________ Purchase date ____________________ Serial No. ______________ Purchase place ____________________ For Information About This Product, call 1-800-330-0712 Model PW2515 Contents Page Getting ToKnow Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety and Warning Information . . . . . . . . .

A covering ensures that your plants won’t be sprayed by the detergents. 2. Start Up ALWAYS use this start up procedure to ensure that the unit is started safely and properly. If water has frozen in the pressure washer, thaw the pressure washer in a warm room before starting. DO NOT pour hot water on or into the pump; internal parts will be damaged. 1. Check engine oil levels. Add oil as necessary. 2. Check fuel level. Add unleaded gasoline (rated 86 octane or higher) as required. DO NOT refuel a

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product. 4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or manufactured by Warrantor. 5. WHAT IS COVERED UNDER THIS WARRANTY:

Check operation of Work Contact Element (WCE) Replace O-Rings Replace bumper Tighten screws Replace gasket Replace bumper Clean drive channel Clean magazine Replace spring Check fitting, hose or compressor Replace and lubricate O-Rings Replace O-Rings Tighten screws and fittings Replace gasket Lubricate nailer Replace spring Replace damaged internal parts Replace guide Use only recommended nails Replace with undamaged nails Tighten screws Replace driver Troubleshooting Guide Stop using nailer im

• LENGTH: 10 1/2” • HEIGHT: 9 1/2” • MAXIMUM PRESSURE: 100 psi • PRESSURE RANGE: 60 - 100 psi Tool Components And Specifications Cap exhaust O CO2 100 psi MAX. Warning label Latch button Magazine Fastener discharge area Work contact element (WCE) Trigger Quick clear nose Adjustable depth control (not visible) Nozzle shield 6 Operating Instructions MXN10400 Nails - Interchange Information MXN104 can use 3/8” to 1-1/4” 18 gauge brad nails designed for the following tools: • Bostitch® BT125SK-2 • C

Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. Operating Instructions MXN10300 O CO2 100 psi Latch Magazine Work contact element (WCE) Fastener discharge area Trigger Fastener loading area Tool Components and Specifications Cap exhaust • REQUIRES: 0.8 SCFM with 10 fasteners per minute @ 90 PSI • AIR INLET: 1/4” NPT • STAPLE SIZE RANGE: 3/8” to 1-1/4” • MAGAZINE CAPACITY: 100 Staples per load, 18 gauge •