The bottom of each guard is numbered, signifying its’ location. 2. Open door and hold the window guard up to the window door frame. NOTE: The angle at the bottom of the guard framework faces towards the outside of the car. The guard framework fits evenly around the window frame. 3. Mark a few holes at the top of the door frame using the pre-drilled holes on the guard framework as a guide. Note: Do not mark holes for the sides or bottom yet. 4. Remove window guard and drill holes as marked wi

Remove seats and seat belts for better access to the windows. 2. Remove plastic trim surrounding the fixed body windows. Save the plastic trim for reinstallation. 3. Determine which guard goes to each window. NOTE: The perforated diamond shaped holes has one side that is smoother than the other. The smoother side goes towards the inside, facing the passenger. DOOR WINDOW GUARDS: 1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim on doors. The top o

This will alleviate the buckling headliner. WindowLatchcoverplateTrim(cut)headlinerifdesired WGI-F1-F2-F3-F4_INST_7-08 FORD VANS FULL SIZE VAN WINDOW GUARDS POSITIONS MODELS WGI-F1, F2, F3 AND F4 POSITION #1 DRIVER SIDE FIRST WINDOW F1-1 POSITION #2 DRIVER SIDE SECOND WINDOW F1-2 POSITION #3 DRIVER SIDE THIRD WINDOW F1-3 POSITION #9 SIDE SWING OUT DOOR F1-9 POSITION #8 SIDE SWING OUT DOOR F1-8 POSITION #10 PASS. SIDE SLIDE DOOR F2-10 POSITION #7 PASS. SIDE SECOND WINDOW F1-7 POSITION #6 PASS. SI

Determine location to obtain both. • With offset bracket positioned against flat surface, (i.e., console, divider wall, etc.), mark and drill 5/16” hole at location of bolt on offset bracket. • Bolt offset bracket to “flat surface” using a fender washer and 5/16” nut. • Bolt C-PED1612 to floor of vehicle using /” x 1” -1 /” hex head lag bolts, depending on particular vehicle application. • Mount optional laptop mounts (C-3090 series), monitor mounts (C-3522), keyboard mounts (C-3329) or tilt

• Using a 9MM socket, remove the spring clip and nut. • Immediately reinstall the nuts only. • Put two #10 washers onto the same bolt on top of the nut. • Put spring clips on top of the washers. NOTE: More washers can be used if needed. Make sure to leave sufficient threads for metric nut. • Using a 7MM socket, put the M4 x 7MM nut (supplied in this kit) on the stud to the hold spring clip and washers. Proceed to the next spring clip. • When all the spring clips are reinstalled, the interior tri

4) Gather all cables to one side and tie off to unused holes on underside of Docking Station. Insert as many zip ties as necessary to secure cables. 7 • 1-800-524-9900 Cable Management (continued) 5) Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion. 6) Tie off cables onto a stationary part of the mounting system. This loop must be large enough to allow full range of expected rotation and extension without stressing connections. Collec

USB 2.0 PERIPHERALS WILL OPERATE IN THIS PORT HOWEVER, USB 3.0 PERIPHERALS WILL NOT OPERATE IN ANY OF THE THREE (3) USB 2.0 PORTS 5 • 1-800-524-9900 Installation 1) Remove the Mounting Bracket from the packaging. Install the Mounting Bracket to the Motion Device using (3) 1/4“-20 x 5/8” long screws (Hardware Kit Item 3). Torque screws to 80 in-lbs (9.0Nm) ± 10%. NOTE: Numerous hole patterns present in Mounting Bracket will accomodate Havis Motion Devices as well as most competitors’ 1/4”-20 Scre

, ROME, GA. 30165 TOLL FREE: (800) 242-0146 DIRECT: (706) 232-0146 FAX: (706) 232-7617 LIMITATION OF LIABILITY THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS; HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES. WARNINGS AND CAUTIONS TO REDUCE THE RISK OF FIRE OR ELEC

Bend window guard so it contours the door as shown in photo #1. Determine the proper window guard for each window. If installing aluminum door panels refer to those instructions at this time. They will need to be installed first. 2. 3. WGI-D22-INST-10-06 INSTALL WINDOW GUARDS • Loosely attach upper mounting bracket to window guard using H” x /” tamper proof screws and flat washers. • Position screen to vehicle as shown in photo #2. • Make sure you have the window guard centered on the d

. 2. Mount window guards: Note: window guards have holes around perimeter for permanent mounting. These holes are not used with hinge kit. They also come flat in shipping. The guard must be pre-bent (outward) so it fits tight against the door window frame. Do not use holes on side of window guard to mount with the hinge application! 1. Hold window guard with pre-assembled hinge and upper bracket onto window frame. 2. Make sure guard is centered on window. 3. Attach hinge to lower door panel