Make sure that none have fallen into the storage bin. 2. The storage bin is for ice use only. Do not store anything else in the storage bin. 3. Keep the area around the icemaker clean. Dirt, dust, or insects in the unit could cause electrical damage to the equipment or harm to individuals. A. Cleaning and Sanitizing Instructions Perlick recommends cleaning and sanitizing this unit at least once a year. More frequent cleaning and sanitizing, however, may be required in some existing water conditi

¦ Turn hand valve counterclockwise on CO2 cylinder to the fully open position. ¦ Turn regulator adjusting screw clockwise until desired pressure is reached (approximately 12-15 lbs.). Tighten stop nut on adjusting screw. ¦ Open shut-off valve on bottom of regulator. CO2 Leak Test Dilute a small amount of liquid dishwashing soap and rub the soapy mixture around each connection. If bubbles appear, tighten connection. Replacing CO2 Gas Cylinder ¦ Turn CO2 hand valve clockwise until seated and close

STAINLESS STEEL ENEMY ¦ Steel wool or steel scouring pads ¦ Cherry/Orange/Olive juice ¦ Chlorine Bleach ¦ Sharp Objects Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice. Form No. Z2219 4 Rev. 4.15.06 Wiring Diagram – Flat Top Bottle Coolers GREEN PLUG-IN-CORD BLACK WHITE WHITE EVAP. FAN EVAP. FAN 2ND FAN ON 4’ THRU 8’ MODELS TEMPERATURE CONTROL RED BLACK TO CONDENSING UNIT INSIDE OF CONDENSING UNIT HOUSING INSIDE OF CAB

Electrical The cabinet must be connected to a separately fused power source (see electrical specification plate) and grounded in accordance with National and Local Electrical Codes. Caution: Do not attempt to operate the equipment on any other power source than that listed on the Electrical Specification plate. IMPORTANT WARNING To avoid compressor damage. DO NOT RUN UNIT IF CABINET HAS BEEN LAID ON ITS BACK If cabinet has been laid on its back for any reason, place it back into the upright posi

12.05.03 INSTALLATION AND OPERATION INSTRUCTIONS CONCESSIONAIRE PORTABLE DISPENSERS Table of Contents PREPARING THE CABINET FOR USE Specifications.........................................................2 List of Included Parts.............................................3 Tools Required.......................................................3 Plumbing................................................................3 Electrical ................................................................3 Inst

¦ Cut a piece of CO2 tubing (red 9/16” vinyl tubing) and push one end onto barbed CO2 outlet to Keg Couplers (See diagram on page3). Position clamp over joint and tighten. Push the other end over the barbed gas inlet on the Perlick Smart Coupler. Position clamp over joint and tighten. Important Notes . CAUTION: If using CO2 as a pressure supply for pumps, pump exhaust must be vented to a well ventilated area to avoid possible asphyxiation. . Never use a single keg to supply more than one beer pu

INSTALLATION AND OPERATION INSTRUCTIONS FLAT TOP BOTTLE COOLER Table of Contents Cabinet Specifications ..........................................2 Installing Uncrating and Inspection ................................3 Plumbing .........................................................3 Electrical..........................................................3 Adjusting Partitions .........................................3 Installing Casters and Legs.............................3 Placing the Cabinet...

Z2149A Rev. 10.11.06 4 5 Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice. Diagram #2 – Beer Pump Form No. Z2149A Rev. 10.11.06 6 Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice. Diagram #3 – Cleaning Diagram Form No. Z2149A Rev. 10.11.06 Cleaning Instructions General Information ¦ The cleaning of beer lines with the new integral flow reversal

6. Do not use a unit with a damaged power cord. The power cord should not be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could result in electric shock or fire. To unplug the unit, be sure to pull the plug, not the cord, and do not jerk the cord. 7. To reduce the risk of electric shock, do not touch the plug or control switch with damp hands. 8. The GREEN ground wire in the factory-installed power cord is connected to a screw on the rear panel where the cord enters

DS Series IMPORTANT INFORMATION Fill out the enclosed warranty card and mail to the Perlick Corporation to register the warranty. If the card is not returned, the warranty period will begin from the date the equipment is shipped from the factory. This manual has been prepared to assist you in the installation of your Direct Draw Dispenser and to acquaint you with its operation and maintenance. We dedicate considerable time to ensure that our products provide the highest level of customer satisfa