Send a 0 (zero) following the command to set the channel power measurement in the current setup. Send a 1 (one) to set the channel power associated with the trace that was most recently uploaded by command #36, Upload Sweep Trace. If Option 6 is installed and the frequency converter module is attached, the frequencies should be scaled by the scale factor of the module. If the module is not attached, frequencies are sent in Hz. Use Control Word A203 to determine whether a module is attached and t

ANRITSU CORPORATION Document No.: M-W1137AE-13.0 Safety Symbols To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment. In addition, there may be other labels attached to products that are not shown in the diagrams

Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation islimited to the original purchaser. Anritsu is not liable for consequential damages. LIMITATION OF WARRANTY The foregoing warranty does not apply to defects resulting from improper or inadequate maintenance by the User, unauthorized modification or misuse, or operation outside of the specifications of the product. No other warranty isexpressed or implied, and the remedies provided herei

Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for consequential damages. LIMITATION OF WARRANTY The foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear. Also, the warranty does not apply to defects resulting from improper or inadequate maintenance by the Buyer, unauthorized modification or misuse, or operation outside the environmenta

Coupled with a wide range of resolution bandwidth choices, you can configure the Spectrum Master to meet your most challenging measurement needs. As the spectrum becomes more and more congested, the ability to measure low level, closely spaced signals becomes more and more important not only for interference detection but also for wireless system planning. Operating convenience is of paramount important importance when equipment is used in the field. The input attenuation value can be tied to th

A complete open, short, and load calibration must be performed before calibration can be turned on. Valid distance to fault plots require a non-zero frequency span. Distance-to-fault measurements cannot be performed with CAL OFF. Attempting to print a display with no printer selected. Select a printer, then retry. Attempting to perform a Power Monitor zero adjust function with no RF detector connected to the Site Master. Attempting to perform a Power Monitor zero adjust function with an input of

STM-64 and OC-192 are widely deployed in today’s networks. While great care is devoted to warrant a very high quality of transport, in the real world of day- to-day installation, commissioning and maintenance activities things are not always running smooth. To this effect, several important tests are always carried out in order to assess the good behaviour of these networks before turn-up. Similarly, when the network has been turned on, it is paramount to keep monitoring the network health at ph

peak 01b = RMS avg 10b = neg. peak 11b = sampling mode) bits 3-4 : Amplitude Units (Log) -(00b = dBm 01b = dBV 10b = dBmV 11b = dBuV) (Linear) – 00b = Watts 01b = Volts bit 5 : Channel Power On/Off bit 6 : Adjacent Channel Power On/Off bit 7 : Units Type (0b = Log 1b = Linear) 295) Status Byte 4170 (0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line) (LSB) bit 0 : Limit Type (0b = Single, 1b = Multiple) bit 1 : Not Used bit 2 : Single Limit On/Off bit 3 : Single Limit Beep L

With features that include a broadband vector modulation bandwidth and large-capacity ARB memory, it supports digital modulation signals for a variety of communication systems. The MG3700A provides optimal performance for generating signals for new wireless communications in advancing broadband technology, as well as for major mobile telecommunication systems such as mobile phones and wireless LANs. Since the standard MG3700A comes equipped with an ARB generator, modulation signals can be output

When both the MU368040A CDMA Modulation Unit that installed MX368041B W-CDMA Software is mounted, one MG3681A can be utilized as a wanted signal source (W-CDMA modulating), an interfering signal source (W-CDMA modulating, CW) and an AWGN source. Furthermore, since mixed Uplink W-CDMA signal and AWGN internally can be outputted by setting the C/N in MX368041B, the base station receiver dynamic range test is realizable by one MG3681A. When both the MU368030A Universal Modulation Unit that installe