K For machines beginning with S/N W11948 and above 2674 N. Service Road, Jordan Station Ontario, Canada L0R 1S0 905/562-4195 Fax: 905/562-4618 Toll-free: 800.263.5798 3765 Champion Boulevard Winston-Salem, NC 27105 336/661-1992 Fax: 336/661-1660 Toll-free: 800.858.4477 Printed in USA For future reference, record your dishwasher information in the box below. Model Number__________________________ Serial Number_______________________ Voltage________________Hertz_____________ Phase_________________

Optional Equipment (consult factory) 70°F/39°C rise built-in booster heater 70°F/39°C rise booster heater element-P/N 111233, Gasket- P/N 109985 1-RDT Right-hand sink - P/N 403562 1-RDT Left-hand sink - P/N 403561 17" Stand - P/N 0708757 17" Storage cabinet - P/N 0703593 6" Stand - P/N 0712393 Peg dish rack - P/N 101285 Flat-bottom dish rack - P/N 101273 Drain water tempering kit - 0712382-1 1 Installation Receiving NOTE: The installation of your dishwasher must be performed by qualified service

Low or no water. Chemicals won’t feed intodishwasher. Door not closed. Main power OFF. Dishwasher OFF. Main water supply off. Solenoid valve defective. Solenoid strainer clogged. Flow washer defective. Timer board defective. Chemical supply low. Supply tubing damaged. Supply tubing kinked. Pick-up tube cloggedTimer board defective. Close door completely. Check breaker on panel. Turn dishwasher ON. Open supply valve. Install repair kit or replace. Clean strainer. Replace flow washer. Test/replace

Improper repairs can lead to considerable equipment damage as well as danger to the user. Problems with the appliance Error display on the programme indicator • When the programme indicators A1 and A2 blink (Fig.4-1). Have you checked if the door is closed properly? • When the programme indicators A1, A2 and A3 blink (Fig.4-2). Have you checked if: the water is turned on and the hose is connected properly; the water supply to the house is on and has sufficient pressure; the water supply hose is

40 Rinse-Aid/Sanitizer Chemical Dispensing Pump - All Models..................... 42 Detergent Chemical Dispensing Pump - All Models.................................... 44 Control Panel (201HT/HTN, 201LT, 401HT/HTN, 501HTN, 501LT)............ 46 Control Panel with Digital Display (501HT)................................................. 48 Door Assy - All Models................................................................................ 50 Panel Assy - All Models..............................

Run LED is litBoard has power Machine is powered up and Run LED Possible bad start switch, scrub switch Unplug low voltage plug. If Run LED lights up: is not litor wiring short (does not apply to S.S. The start switch or scrub switch failed in the closedPizio switch on model 501 or UH200)position, or there is a wiring short Machine is powered up and Run LEDCheck voltage is not lit after unplugging the low voltage plug2. Wash pump runs but nothing else works 4 amp board output fuse is blownReplac

Overview and Operation . Looking after your Dishwasher . Troubleshooting . Installation . General Information . Circuit Diagram . Technical Data 1. Before You Start At Time of Delivery Check packaging and dishwasher immediately for signs of transport damage. If the appliance is damaged DO NOT USE. Contact your supplier or customer services. Please dispose of packaging materials properly. During Installation • Site the dishwasher and connect in accordance with the installation instructions. • The

1 — 0707549 PUMP/MOTOR ASSEMBLY COMPLETE 1.4HP(575V/60/3PH).............................................. 1 REPLACEMENT PARTS WASH EXTENDED WASH CYCLE POWER OFF RINSE PRESSURE 4 5 7 6 8 92 3 1 Figure 36 - MH-60/6N/6L Control Panel and Gauges REPLACEMENT PARTS MH-60/6N/6L CONTROL PANEL AND GAUGES Fig. 36 Part Item No. No. Part Description Qty. 1 0501361 SWITCH, ON-OFF ....................................................................... 1 2 112390 LITE, RED (POWER) .............................

d. Release the toggle switch to stop the water flow. e. You have complete the booster priming process. NOTE: Push the Installation and Service toggle switch to the ON position. Electrical power is now supplied to the machine. ! WARNING: Failure to prime the booster may cause damage to the booster elements and other electrical components and will void the warranty, 4. After plumbing and electrical connections are completed, check the machine for water leaks by depressing the ON/FILL/OFF/DRAIN to

low ..................Hot water supply min. 145°F/66°C Water on floor around Pump seal leaking ...............................Replace machine Rinse drain in wash area plugged .......Clear obstruction, clean machine Wash return screen in detergent..........Clean tank plugged Drain screen under detergent .............Clean tank plugged Main drain plugged .............................Clean Detergent tank covers are not .............Position all top covers to completely cover positioned properly cau