Passes should be made across the length and width of the garden alternately. Rocks which are turned up should be removed from the garden area. See Figure 8. Figure 7 Figure 8 Handle Pressure Further control of tilling depth and travel speed can be obtained by variation of pressure on the handles. • A downward pressure on the handles will reduce the working depth and increase the forward speed. • An upward pressure on the handles will increase the working depth and reduce the forward speed. The t

Make all adjustments or repairs before using the unit. • This unit was not designed to be used as a brushcutter. Do not attach or operate this unit with any type of brushcutting blade or brushcutting attachment. SAFETY WARNINGS FOR GAS TRIMMERS Gasoline is highly WARNING: flammable, and its vapors can explode if ignited. Take the following precautions: • Store fuel only in containers specifically designed and approved for the storage of such materials. • Always stop the engine and allow it to co

2 54 1757842 Knob.......................................................... 1 2 1753986 Ignition Key...................................... .......... 2 55 1739941 Brake Arm.................................................. 1 3 1739937 Idler Arm.......................................... .......... 1 56 1765535 Extension Spring....................................... ? 4 1733398 Lock Nut, 3/8-16.............................. .......... 3 57 1107385 Flat Washer, 1/2”..............................

Improper adjustment will cause stalling when splitter is under load, hard starting and higher fuel consumption. Refer to the separate engine manual packed with your log splitter for carburetor adjustment information. NOTE: A dirty air cleaner will cause engine to run rough. Be certain air cleaner is clean and attached to the carburetor before adjusting carburetor. Do not make unnecessary adjustments. Factory settings are satisfactory for most applications and conditions. MAINTENANCE Hex Bolt

Snowthrower TRACTOR ASSEMBLY S/N 420280100101- 420280199999 85 0 J41 40 . . Ve TOUCH-UP PAINT SERVICE PARTS 200 Black Spray Paint 202 Loctite 242 201 Green Spray Paint 203 Tire Chains 7Г* Щ. 32 35 «к 29 Ч1 2 Model 42028 Ref.# Part# Description Qty. Ref.# Part# Description Qty. 1 1703539 Handle Grip............................................ 2 51 1756065021 Frame.................................................. . 1 2 1750796 Bumper..........................................

BOX 368022 • CLEVELAND, OHIO 44136-9722 FORM NO. 770-95-6B Model 406 6B — Page 2 Model 406 PARTS LIST FOR MODEL 406 TILLER REF. NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 710-0412 Hex Bolt 1/4-28 x .75" Lg.* 56 736-0169 L-Wash. 3/8" I.D.* 2 720-0180 Grip 57 712-0798 Hex Nut 3/8-16 Thd.* 3 747-0517 Clutch Lever 59 15393 Brkt. Reinforcement 4 712-0117 Hex Cent. L-Nut 1/4-28 Thd. 61 784-0026 Tine Shield Ass’y. 5 710-0458 Carr. Bolt 5/16-18 x 1.75"* 62 714

ELECTRICAL SYSTEM I. DRIVE TRAIN IV. FUEL SYSTEM V. CHASSIS VI. HYDRAULIC SYSTEM VII. ENGINE VIII. TRACTOR ATTACHMENTS f?j bi pa pn ra ra ra MEDIUM FRAME SERIES TRACTOR Rev. 11-90 TABLE OF CONTENTS GROUP 1. GENERAL SERIAL NUMBER INFORMATION...............1-1 SPECIFICATIONS..............................1-2 MAINTENANCE CHART........................1-5 LUBRICATION POINTS (GEAR DRIVE) .........1-6 LUBRICATION CHART (GEAR DRIVE)..........1-7 LUBRICATION POINTS (HYDROSTATIC DRIVE)..

781-1056 Upper Handle Bracket 6. 710-0726 Hex Cap Screw 5/16-12 x.750 7. 720-04072 Handle Knob 5/16-18 8. 710-1174 Carriage Bolt 9. 731-04911 Nozzle Handle Clip 10. 749-04165 Lower Handle 11. 711-1293 Studs 12. 710-0703 Carriage Screw 1/4-20 x.75 13. 712-0397 Wing Nut 1/4-20 14. 710-1611B TT Screw, 5/16-18 x .750 15. 710-0599 Screw, 1/4-20 x .500 16. 712-0442 Cap Lock Nut, 1/4-20 17. 710-0751 Hex Cap Screw 1/4-20 x.620 18. 681-0195 Hose Base Adapter Assembly (Incl. Ref.# 19-21) 19. 716-0104 E Ri

770-5307D IMPORTANT RULES FOFI SAFE OPERATION A THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD EN- A DANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTE OPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL— HEED ITS flQI WARNING. j DANGER J Your unit was built to be operated according to the rules for safe o

Drain all fuel from the fuel tank into a container. Do not use fuel that has been stored for more than 60 days. Dispose of the old fuel in accordance to local regulations. 2. Start the engine and allow it to run until it stalls. This ensures that all fuel has been drained from the carburetor. 3. Allow the engine to cool. Remove the spark plug and put 1 oz. (30 ml) of high quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug. NOTE: Remo