Contents General Safety Rules...........................................................................................................................................................................3 Specific Safety Rules for Circular Saws........................................................................................................................................4 Tool Description.........................................................................................................

Using too small of an extension cord can cause the cord to overheat. Extension Cord Ratings Cord Length Size (AWG) <25 Ft. 14 25-50 Ft. 12 50-100 Ft. 10 >100 Ft. Not recommended Personal Safety > Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. > Use personal protective equipm

The extraction adapter (4.3) can be removed if necessary. To do this, press the locking button (4.1), draw the extraction adapter backwards and pull off. To reattach the extraction adapter, insert it as shown in Fig. 4 and slide it towards the Smooth start-up sanding pad until the locking button (4.1) latches The smooth start-up ensures jolt-free startup. into place. 4 Edge protector 5.1 The edge protector (5.1) prevents the sanding pad from touching the edge perpendicular to a surface (e.g. whe

Manual de instrucciones Pagina 22 - 31 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. Instruction manual Guide d’utilisation Manual de instrucciones MFT/3 MFT/KAPEX 475235_003 2 Table of Contents Health hazard by dust Technical data 3 Symbols 4 Design 4 Intended use 4 MFT/3: Setting up and assembly 5 Step 1: Setting up 5 Step 2: Trim splinter guard 5 Step 3: Setting up the guide rail support 6 Step 4: Attaching the guide rail 7 Step 5: Attaching the pre-set profi le setting r

2.. Extension cable If an extension cable is required, it must have a sufficientcross-section so as to prevent an excessive drop in voltageor overheating. An excessive drop in voltage reduces theoutput and can lead to failure of the motor. The table besideshows you the correct cable diameter as a function of thecable length for the router OF 2000 E/1. Use only U.L. andCSA listed extension cables. Never use two extension cablestogether. Instead, use one long one. Note: The lower the AWG number, t

Use this sander only for dry sanding. The user bears sole responsibility for any damage or accidents resulting from incorrect use. The mains voltage must correspond to the voltage on the rating plate! To start the tool, push the switch (1.1) forwards. Slight pressure on the rear end of the switch is sufficient to switch the tool off. Extension cord If an extension cord is required, it must have sufficient cross-section to prevent an excessive drop in voltage or overheating. An excessive drop in

To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. Technical data ETS 150/3 EQ ETS 150/5 EQ Wattage W 310 310 No load speed rpm 6 000 - 10 500 6 000 - 10 500 No. of strokes spm 12 000 - 21 000 12 000 - 21 000 Sanding stroke mm (in.) 3.0 (0.12) 5.0 (0.20) Sanding base, O mm (in.) 150 (5.9) 150 (5.9) Weight kg (lbs) 1.8 (4.0) 1.8 (4.0) Safety level U

For this reason, it is recommended that you spend some time practicing using the Domino joiner before you begin using it for your fine woodworking projects. For best results, observe the following tips: > Always secure the workpiece firmly. > Hold the Domino Joiner firmly by the handles and keep it flat against the workpiece. > Plunge the mortising bit into the workpiece with a slow and steady pace. Choosing the Right Domino Tenon Size Because the Domino system is a form of the classic mortise a

464 760_004 Manual de instrucciones Lijadora excentrica Pagina 12 - 16 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work area 1 Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2 Do not operate power tools in explosive atmospher

Metal and materials with an asbestos content must not be processed with these tools. The machine is particularly suitable for processing smaller surfaces and overhead work because of its size, its weight and its output. The machines must not be damp nor operated in a damp environment for electrical safety rea connecting or disconnecting the power cable! 3 4 The switch (1.1) acts as an ON / OFF switch (I = ON / 0 = OFF). 1.1 Electronic control ELECTRONIC The RTS 400 EQ has an electronic control w