SMOKE ALARMS MUST NOT BE USED WITH DETECTOR GUARDS UNLESS THE COMBINATION OF ALARM AND GUARD HAS BEEN EVALUATED AND FOUND SUITABLE FOR THAT PURPOSE. The ionization type alarms are generally more effective at detecting fast, flaming fires which consume combustible materials rapidly and spread quickly. Sources of these fires may include flammable liquids or paper burning in a waste container. The photoelectric type alarms are generally more effective at detecting slow, smoldering fires which smold

However, to reduce the chance that fires will start, practice fire safety rules and prevent hazardous situations. 6 ! ! TROUBLESHOOTING DANGER: Always turn off power at main fuse box or consumer unit before taking trouble- shooting action. WARNING: DO NOT disconnect battery or mains power to quiet an unwanted alarm. This will remove your protection. Fan the air or open a window to remove smoke or dust. For Models GC240, I240C, PADC240, PG240, PAR230 and IAR230C you may also use the False Alarm C

Always turn off power to smoke alarm before cleaning. • Using the soft brush or wand attachment to a vacuum cleaner, vacuum all sides and cover of smoke alarm. Be sure all the vents are free of debris. • If necessary, turn off power and use a damp cloth to clean smoke alarm cover. IMPORTANT: Do not attempt to remove the cover or clean inside the smoke alarm. THIS WILL VOID YOUR WARRANTY. REPAIR ! CAUTION: Do not attempt to repair this smoke alarm. Doing so will void your warranty. If smoke alarm

If a bedroom area hallway is more than 9 m long, install a smoke alarm at each end. •Install a smoke alarm at the top of a first-to-second floor stairwell. Key • Smoke Alarm . Smoke Alarm with False Alarm Control 2 IMPORTANT SMOKE ALARM PLACEMENT AND EXCEPTION INFORMATION: •Install a smoke alarm as close to the centre of the ceiling as possible. If this is not practical, mount no closer than 10 cm (4 inches) from a wall or corner. Also, if local codes allow, install smoke alarms on walls, betwee

The Firex Heat Alarm, Model 5700, is a fixed temperature unit that detects heat at 135°F (57°C) or greater. It relies on a thermistor that is sensitive only to temperature. When the temperature reaches 135°F (57°C) or greater, the alarm is triggered. The 5700 requires 120V AC power and includes a 9V battery back-up for added protection in the event of a power failure. The 5700 heat alarm is interconnectable with other AC/DC Firex heat alarms, smoke alarms, smoke/co combo alarms, and carbon monox

7832 U.S.A. PLEASE READ AND SAVE INSTALLER: Please leave this manual with the product. © 2002 Maple Chase 110-666C SMOKE ALARM DESCRIPTION Model GC240 Ionisation 230V AC smoke alarm with False Alarm Control Model I240C Ionisation 230V AC smoke alarm with 9V battery back-up and False Alarm Control Model IAR230C Ionisation 230V AC smoke alarm with rechargeable battery backup and False Alarm Control Model PG240 Optical 230V AC smoke alarm and False Alarm Control Model PAD240 Optical 230V AC smoke a

5. If interconnection is desired, connect orange wire from connector to interconnect wire between smoke alarms. See section, “Interconnecting Smoke Alarms.” 3 NOTE: If this will be a single-station smoke alarm, cover orange wire with electrical tape and tuck into ceiling, wall, or pattress. ELECTRICAL BOX OR PATTRESS ELECTRICAL BOX OR PATTRESS BLUEORANGEBROWN LINEINTERLINKNEUTRAL CEILING BLUEBLUEORANGEBROWN LINENEUTRALINTERLINK CEILING MODELS GC240, I240C, PG240, PAD240, PADC240 MODELS IAR230, P

Normal “Standby” Silenced Mode Note that the strobe module, when installed, will not stop operating when the silence function is engaged. Mode Wiring For appropriate duct detector wiring terminals, please refer to detector and remote accessory installation instructions. Products 591 Series Remote Accessory Controllers 591W Remote Indicator/Control Assembly w/White Single Gang Cover Plate 591R Remote Indicator/Control Assembly w/Red Single Gang Cover Plate 591S Remote Indicator/Control Assembly w

Installation of Smoke Alarm This smoke alarm should be installed in accordance with NFPA’s Standard 72 (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269) and any local codes that apply. For the AC and AC/DC direct wire smoke alarms use #18 AWG minimum solid or stranded wire. When interconnecting, maximum wire length between any two is 1,500 feet for #18 AWG or 4,000 feet for #14 AWG (20 OHMS loop resistance). DO NOT connect to any other type or model of heat or smoke ala