Back of Chime Tune Setting (Not used on all models) Note: Some models might require the use of tweezers to remove and replace the jumpers. 595-5649-05 -3 Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages 2 and 3). • Check orientation of push button battery (See page 3). • Check push button battery charge, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near met

Manual Storage Slot: A convenient slot in the base has been provided to insert the manual for future reference. Volume Control: Turn the volume control clockwise to increase the volume or counterclockwise to decrease the volume. Reset Button: This button has a dual purpose. 1) To return to the first tune in a Group when using the Tune Selection Button to cycle through the tune selections. 2) To reset the chime in case of power failure or surge. Cover Pin: A notched cover pin is located on two si

Plug wireless chime into wall outlet. Note: The volume control is on the back of the wireless chime. Unplug chime to adjust volume. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to bypass this safety feature. ©

In typical use, alkaline batteries will last up to three years. WARNING: To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. Figure 1 1. Install alkaline type A23 12 volt push button battery (included). Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). See diagram inside push button for correct battery orientation. Note: If batteries are preinstalled, remove orange b

In typical use, alkaline batteries will last up to three years. 1. Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Make sure battery is oriented properly (See page 4). 2. Install3alkaline“D”batteries. Make sure batteries are oriented Figure 1 + + + BatteryBatteryBattery Chime Volume Jumpers - - - properly (see Figure 2). 3. Test range. Temporarily position chime and push button Cover where you want th

• Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note:All modelshave bothfrontandbackdoortunecapabilities.Werecommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come facto

• Automatically turns light off. • Dusk Accent lighting. • Photocell keeps the light off during daylight hours. This package includes: • Lantern • Easy to use universal mounting bracket (X-Bar) • Mounting hardware • Wire nuts Requirements • The Light Control requires 120 volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time Works: Day Night Test 5 Seconds x x Auto 1, 5, or 10 M

TFigure 3 - Pin for Hanging Cover Hang Pin, Snap-On Type Illustrations may vary from actual chime unit. Snap-On Cover Base Orientation Marking Hang Pin, Slide-On Type FRONTUPTRANSFigure 5 - Mounting Hang Bracket Cover Illustrations may vary from actual chime unit. Hang Bracket Cover Base Orientation Marking Hang Bracket Chime Base (Mounted Vertically) Hang Bracket Slot FRONTUPTRANSFigure 5 - Mounting Hang Bracket Cover Illustrations may vary from actual chime unit. Hang Bracket Cover Base Orient

This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIR OR REPLACEMENT SHALL B

In typical use, alkaline batteries will last three years. 3.Test Range. Temporarily position chime where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 1. Open chime case: Press in catch on bottom of chime and lift the case open. Battery Chime Volume 2. Install the 3 alkaline "D" batteries. Make sure batteries are oriented properly. 4. Mount accessory chime. Chime can be mounted by using 3 holes in the back of c