10. Delay/Reverb: This switch selects between Delay or Reverb effects. Press switch in to choose Delay. 11. Effects: This control increases the effect signal level and mixes it with the instrument’s signal. Turn this control clockwise to add the desired level of effects. 12. Chorus: By pressing in, this switch activates a lush Chorus effect. (Note: When Chorus is activated, it is always mixed with either Delay or Reverb, as selected by the Delay/Reverb switch.) 13. Aux In: This is a 3-conductor,

The gain is applied before the tone controls. 13.) Bright - this enhances upper Treble frequencies and helps provide clarity to darker sounding guitars. 14.) Rhythm Volume - this is a volume control for the Rhythm Channel only. 15.) Rhythm Bass - this passive EQ adjusts the low frequency equalization of the amplifier. For tighter low-end response, set the Bass control to lower settings. This is particularly helpful when using the amp at very loud volume levels. 16.) Overdrive - this increase

Use in its lower ranges to produce less distorted tones. As you increase the amount of gain, the tonality will shift from a classic rock-type sound to a heavier, modern tone. 4. Volume (Lead): This controls the overall volume level of the Lead channel only. 5. Channel: This switch selects between the Lead and Rhythm channels. 6. Volume (Rhythm): This controls the overall volume level of the Rhythm channel only. 7. Bass: This controls the bass frequencies for both channels. For a “tighter” bass r

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. kustom.com ENGLISH kustom.com FRENCH KXB200H/HR Control Panel 1 2 3 4 6 7 85 109 11 1312 KXB200 1. 0 dB Input: .-inch input that is intended for bass guitars with standard, passive electronics. 2. –6 dB Input: .-inch input that is optimized for bass guitars with active electronics. 3. Gain: Controls the input level to the

Your KG Model draws on decades of amp design and manufacturing experience at Kustom. This model was built from the ground up to offer world-class tone, useful features and reliable performance. Inside this manual, you’ll find valuable information about the amp’s controls and specifications. Being familiar with its features will help you effectively dial in different tones. We wish you many years of enjoyment with your Kustom amplifier. kustom.com FCC Statements 1. Caution: Changes or modificatio

The amplifier’s internal speaker is disconnected when this jack is used. 15. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When illuminated, it shows that your amplifier is ready to be played. To turn amplifier on, press switch upward. To turn amp off, press switch downward. kustom.com KG100FX112 Back Panel External Speaker: This is a two-conductor, .-inch external speaker jack. (Note: This jack is wired in series with the amp’s internal

It will boost or cut by 14 dB at 60 Hz. 6. Lo-Mid: This control adds thickness and body to your tone. It will boost or cut by 12 dB at 340 Hz. 7. Hi-Mid: This control adds punch to your overall tone. It will boost or cut by 10 dB at 2 kHz. 8. Treble: Increasing this control will add presence and attack to your bass tone. It will boost or cut by 15 dB at 10 kHz, perfect for enhancing “slap” and pick playing. 9. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compa

2. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfe

ENGLISH kustom.com FRENCH kustom.com KG210FX Control Panel 1 2 3 4 6 7 85 9 10 11 12 13 1. Input: .-inch 2-conductor input jack that is intended for electric guitar but will accept other instruments as well. 2. Gain (Lead): Adjust this control clockwise to increase the amount of distortion. Use in its lower ranges to produce less distorted tones. As you increase the amount of gain, the tonality will shift from a classic rock-type sound to a heavier, modern tone. 3. Volume (Lead): This controls t

8. EQ-800: This active control adjusts the hi-mid frequencies to boost or cut by 12 dB centered at approximately 800 Hz. 9. EQ-2K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 2 kHz. 10. EQ-5K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 5 kHz. 11. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compact Disc, MP3 player or other audio device. The overall