No further manual setting is necessary. SETTING THE STARTING DATE OF DAYLIGHT SAVING TIME Example: Daylight saving time starts on Sunday, March 25, 2001. Year DateMonth D.S.T. START SELECT CHANGE SET SELECT D.S.T. START CHANGE SET SELECT D.S.T. START CHANGE SET 16 SELECT D.S.T. START CHANGE SET Step 1 Press the SELECT button and position the " " mark at the "D.S.T. START". At that moment, the "Year" flashes. (The flashing means it can be changed.) Change the "Year". In case of the example, press

[6]=ENABLE CIRCUITS This function requires the administrative password. Use this function to enable and disable bell relays during circuit wiring or maintenance. This function can also hold back clocks to manually adjust for daylight saving time in the fall if you do not use the [7]=DAYLIGHT SAVINGS function. Note: Disabled relays will ignore any schedules, and you cannot manually turn them on. See Enabling the Relays on page 2-4. 24A715/24A715M Master Clock Installation Manual [7]=DAYLIGHT SAVI

The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five (5). A NOTE ABOUT THE LITHIUM BATTERY The Lithium Battery (coin cell) contained in this product is NOT user-replaceable. When replaced by an authorized Service Center, used batteries should be disposed of according to the manufacturer’s instructions. Table of Contents SECTION 1—INSTALLATION General Informa

No warranties are given with respect to products purchased other than from Lathem or an authorized Lathem reseller and any such products are purchased "as is, with all faults." In no event will Lathem be liable for any direct, indirect, special, incidental or consequential damages arising out of or in connection with the delivery, use or inability to use, or performance of this product. In the event any limited remedy given herein shall be deemed to have failed of its essential purpose, Lathem's

4. Depress the time type setting lever (Figure 2, Number 4). Using a small screwdriver or similar tool, rotate each individual date and time type wheel down to the correct date and time. (Note: Month and date type wheels must be reset manually the first day of each month.) 5. Depress the number type setting lever (Figure 2, Number 5) and rotate the number type wheels (Figure 2, Number 6) to the correct position. 6. Close the top frame and insert the locking pin, positioning the pull ring down an

80 PAYCLOCK & FACEIN USER’S GUIDE • Move the face back until there is 9 to 25 inches between their face and the terminal. • Turn the head fully to the right. • Turn the head fully to the left. • Raise the head up slightly. • Lower the head down slightly. • Move the face back from the terminal until there is 9 to 25 inches between the face and the terminal (if adjust positioning message is still displaying). • Resume small head circles to the right (if adjust positioning message is still displayi

Do not put a heavy object on the time recorder, or forcefullypress the time recorder onto the back-plate. This may cause trouble with the punching mechanism. Lithium battery contains perchlorate material – special handling may apply. Please go to the web site for information about proper methods of disposal. About this Manual This manual will guide you through the installation, set up and use of your 800P TruAlign Time Recorder. Optional Accessories . E8-100 Weekly timecard for the 800P (pack of

All rights reserved. Contents Here’s all the information you need for setting and operating your new Lathem time recorder. Service information is also included in this manual, in case any problems ever arise. Thank you for choosing a Lathem time recorder. Should you ever need assistance, please let us know. Ordering Accessories ................................................ 2 Setting the Time ........................................................ 3 Changing the Ribbon........................

2. This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which has had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired other than in accordance with instructions furnished by Lathem. 3. This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any expendable parts that are readily replaced due to normal use. 4. The sole responsibility of Lathem under t

It has been tested and found to comply with the limits for a Class A computing devise pursuant to Subpart J of part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of the equipment in a residential area is likely to cause interference, in which case, the user, at his own expense, will be required to take whatever measures may be required to correct the interference. This document is a confidential