12082 Western Avenue, Garden Grove, CA 92841 (800) 874-3005 VOICE • (800) 772-2889 TTY/TDD • (714) 897-4703 FAX email: ameriphonecs@plantronics.com website: ® XL The Extra Loud & Clear XL-40 AMPLIFIED TELEPHONE with lighted keypad! Operating Instructions M46802 ©AMERIPHONE® XL-40 5270-4023 .A4/03 E N G L I S H E S P A N O L F R A N C A I S Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric sho

• Setup special features Installing the Backup Batteries To add extra brightness to the Dialogue XL-25s’s ring flasher when you receive calls, install one 9 Volt alkaline battery (not included). Note: For your safety always unplug the phone line before you install or replace the backup battery. 4 Figure 3 To install new battery: 1. Slide open the battery compart-ment cover on the bottom of the telephone, (Figure 3). 2. Install one fresh 9-volt battery. The battery indicator on the base unit will

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of th

Attach the Dialogue LVD cable to the connector on the back of the Dialogue VCO. Be careful not to bend any pins. Figure 36 - Audio Output Socket Figure 37 - Connecting the Speech Processor DIALOGUE VCO M1 a. a. a. a. a. POWER RELAY REL MGS SPACEAUTO ANS SIGNAL M2 M3 M4 M5 SELECT MEMORY b X HOLD PROG LO HI FLASH REDIAL TONE VOL AMPLIFY Q Z ! $ () = " / ' + , . ? : ; b. b. b. b. b. 18 Figure 38 - Connecting the Dialogue LVD IN TTY/TDD MANUAL AUTO Connecting to the Q-90 Printer The Dialogue VCO can

to turn on phone. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 • • Voice Activated answering is off, (RC-200 only). Ring volume set to Hi. Unanswered call indicator is on. ”0“ (operator) is programmed into Voice Mail indicator is off, (RC-200). Remote Flash switch is off, the first memory location of M1. Press 0 on the keypad to Press SCAN button. turn it off; or Press 1 key on the keypad to turn it on. 32 Press 0 key to turn it off; or Press SCAN button. Press 1-9 keys to turn it on. See Page 5 for rate selecti

When the desired memory location is lit, press the SCAN button again to select. 4. The DIALOGUE RC automatically dials the number selected. 5. Press the ON/OFF Figure 16 button to hang up. Dialing using the Remote Transmitter A. With Scan function on: 1. Press the Remote Transmitter to begin scanning. FLASH/PAUSE REDIAL MUTE ON/OFFHEADSET MIC Figure 17 2. When the desired memory location is lit, press the Remote Transmitter. The DIALOGUE RC automatically dials the number selected. 3. Press the R

Please read the Operating Instructions booklet to learn more about the advanced features of the Q90D. Quick Guide Ameriphone products are manufactured by Clarity®, a Division of Plantronics, Inc. 4289 Bonny Oaks Dr., Ste. 106, Chattanooga,TN 37406 VOICE (800) 426-3738 TTY (800) 772-2889 © 2004 Plantronics, Inc. 79040.000 B2/04. Installing and Using Your Q90D Installing and Using Your Q90D Setting Up Your Q90D Lock Switch 1. Slide the LOCK switch (which is located on the right side of the unit be

Read and understand all instructions. Observe all warnings and other markings on the product. 2. During thunderstorms, avoid using telephones except cordless models. There may be a slight chance of electric shock from lightning. 3. Do not use a telephone near a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where gas is leaking. 4. Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, o

3 E N G L I S H Important Safety Instructions CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalent Number of

Help from Ameriphone For help with using your DIALOGUE JB-20 , call our Customer Relations department at 800-894-3005. Please make sure your DIALOGUE JB-20 package includes the items shown in Figure 1. Base Unit CHAPTER 3 FEATURES IDENTIFICATION RINGER TONE selector HOLD button Ringer control switch (volume) Audio Output jack Tone / Pulse switch Emergency buttons Braille characters Raised letters for easy identification REDIAL button MEMORY button HANDSET VOL control (volume) FLASH button PROG b