Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be

Liste de Repuestos FP202800 16 1 2019 14 13 22 2 8 9 10 12 476 5 3 17 15 11 24 21 23 22 25 18 la lista de repuestos No. de Numero No. de Numero Ref. Descripcion de pieza Ctd. Ref. Descripcion de pieza Ctd. 1 Tapa 1 16 Cordon electrico FP202826AV 1 2 Accesorio de la cubierta 1 17 Tornillo M3x10 1 3 Interruptor de 18 Ensamblaje de bomba/motor FP202824AV 1 encendido/apagado FP202833AV 1 19 Cubierta del motor 1 4 Tornillo M3 x .15 6 20 Cubierta del extremo 1 5 Distribuidor FP202832AV 1 21 Sopo

MANUAL 2. Follow all local electrical and safety codes as well as in the US, National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA). REMINDER: Keep your dated proof © 2007 IN614204AV 5/07 24 Sp Oilless Compressors General Safety Information (Continued) 3. Only persons well acquainted with these rules of safe operation should be allowed to use the compressor. 4. Keep visitors away and NEVER allow children in the work area. 5. Wear safety glasses and use hearing protection w

Ajustes manuales de los instrumentos de carga/descarga y valvula de 7. RESPONSABILIDADES DEL GARANTE BAJO ESTA GARANTIA: Reemplazar, componentes que esten defectuosos, se hayan danado o hayan de validez de la garantia 8. RESPONSABILIDADES DEL COMPRADOR BAJO ESTA GARANTIA: A. Suministrar prueba fechada de compra y la historia de B. Tener cuidado al utilizar el producto, tal como se indica(9. EN QUE CASOS EL GARANTE PROPORCIONARA REEMPLAZO planificado de acuerdo a la disponibilidad de compresores

Wear ANSI approved Z87.1 safety glasses. 2. Drain moisture from tank by opening drain valve underneath tank. Tilt tank to remove all moisture. 3. Clean dust and dirt from tank, air lines and pump cover while compressor is still OFF. LUBRICATION This is an oilless type compressor requiring no lubrication. THERMAL OVERLOAD PROTECTOR This compressor is equipped with an automatic reset thermal overload protector which will shut off motor if it becomes overheated. 4 If thermal overload protector shut

Once completed, it is not necessary to repeat.) 1. Do not attach a hose or any other fitting to the compressor. 2. Turn on/off switch to OFF position. 3. Plug in power cord. 4. Turn on/off switch to ON position. Allow compressor to run for 5 minutes. 5. Turn on/off switch to OFF position. 6. Unplug power cord. BEFORE EACH STARTUP OPERATING PROCEDURE 1. Connect air hose to open port located below pressure gauge. 2. Attach the necessary fitting or tool to open end of air hose. 3. Turn on/off switc

2. QUIEN OTORGA ESTA GARANTIA (EL GARANTE: Campbell Hausfeld / The Scott Fetzer Company 100 Production Drive, Harrison, Ohio 45030 Telefono: (800) 543-6400 3. QUIEN RECIBE ESTA GARANTIA (EL COMPRADOR): El comprador original (que no sea un revendedor) del producto Campbell Hausfeld. 4. PRODUCTOS CUBIERTOS POR ESTA GARANTIA: Cualquier compresor de aire Campbell Hausfeld. 5. COBERTURA DE LA GARANTIA: Los defectos substanciales de material y fabricacion que ocurran dentro del periodo de validez de l

V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Specifications Electrical Requirements 120 V~ / 60 Hz / 9.3 A Air Hose Connection 1/4” 18 NPT Maximum Air Pressure 155 PSI Air Pressure Cut On 125 PSI Air Tank Capacity sku 99780: 17 Gallons sku 99781: 26 Gallons Air Flow Capacity 6 SCFM @ 40 PSI 4 SCFM @ 90 PSI Motor 4 HP, 13000 RPM 233060 Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please c

Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacemen