Test the supply volt- floor drain vacuum valves to provide maximum flow. age, amperage draw, wire size against factory specifications and local codes. Test the operating refrigerant The auto vac manufacturer has a special valve that plugs pressures and corresponding components to factory into the skimmer before the auto vac hose. These spe specifications. Adjust refrigerant according to the sub cial valves will properly regulate the water flow through cooling reading and factory specification. t

When setting the timer, be sure that you shut off the pool circulation pump circuit breaker. Then follow the timer manufacturers instructions to prevent electrical shock. Consult your dealer first. INITIAL HEAT UP TIME (HEATERS) You should start by letting the circulation pump run 24 hours a day until the pool reaches the desired temperature. Once the pool is up to your desired temperature you should reset the timer for a cycle of 6 to 18 hours per day during the hottest part of the day. Heat up

Check suction piping and valve glands on any suction gate valves. b. Secure lid on pump strainer pot and make sure lid gasket is in place. c. Check water level to make sure skimmer is not drawing air. 2. Pump will not prime--not enough water. - Remedy: a. Make sure suction lines, pump strainer, and pump volute are full of water. b. Make sure valve on suction line is working and open, (some systems do not have valves). c. Check water level to make sure water is available through skimmer. 3. Pump

This innovative hydraulic design moves water more efficiently and more quietly than competitive pumps. Under typical operating conditions, WhisperFlo offers the highest water flow of any high performance pump-yet with the lowest electrical consumption. And, WhisperFlo is designed to be a tireless workhorse. Its engineered thermoplastic housing withstands extreme heat and resists corrosion. The commercial grade motor frame has a rust-proof, stainless steel motor shaft and sealed bearings that ne

The Smart pHTM is a Class 1 product for protection against electric shock and a Type 1 product with regards to disconnection of the control circuits. Observe the following safety precautions: . Do not permit anyone untrained or under the age of 18 to use this product. . Unit must be properly connected to earth ground. . Never apply power when front panel is not secured in the closed position. . Never service unit with power applied, always turn OFF main circuit breaker to unit and all equipment

You can schedule start and stop times for each feature. All Features are operated using Flow control. The Feature mode and Filter mode are run simultaneously. The three types of features are; Features 1 & 2, Features 3 -9 and M.O. Flo: Features 1 and 2 Feature 1 and Feature 2 run for a pre-defined duration with a specifically set flow. If Feature 1 or Feature 2 buttons are pressed, all other Features are temporarily deactivated. Feature 1 or Feature 2 cannot be used in Backwash Mode. Features 1

Installing light fixture during new pool construction ............................................................................................ 3 Section II. Replacing light fixture in existing pool ................................................................................................................... 4 Section III. Replacing a lamp only ............................................................................................................................................ 5 Se

G • Rev. G • Rev. G 10-29-07 2. To remove light assembly, remove the special pilot screw at top of face ring, remove light assembly from niche, and place assembly on deck. WARNING Be sure to keep the special pilot screw from this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard which could result in death or serious injury to pool users, installers or others du

Pltd. 5 1 35-4894 Pump Tri Pod Base Plastic 4 1 35-3775 Seal Bracket -Plastic 3 2 35-4294 Screw, Cap 3/8 -16 x 1 1/4” Cad. Pltd. 2 1 35-3750 Shaft Extension -Bronze 1 Motor Item Qty. Part No. NAME OR DESCRIPTION LIST OF MATERIAL OR PARTS LIST 7 SPECIAL INSTRUCTION FOR TWO SPEED ENERGY MASTER HYDROPUMP: The performance of this pump will be the same at high speed as the same model single speed pump, both hydraulically and prime wise. At low speed the pump will produce one half the flow and the pre

Make sure pool water is midway of skimmer opening. NOT PRIME: 2. Make sure strainer basket is not clogged. 3. Make sure strainer basket is positioned properly! 4. Tighten lid down snugly. 5. Make sure strainer pot is full of water. 6. TIghten all fittings and seal all joints on suction side. 7. Clean skimmer and pump strainer baskets. 8. Remove pump lid and check for clogging. 9. Open all valves in return and suction lines. 10. Remove and replace pump seal if needed. 11. Check voltage at pump to