• The heater must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. • Any safety screen or guard removed for servicing the heater must be replaced prior to operating the heater. • Keep heater area clear and free from combustible materials, gasoline and other flammable vapors and liquids. • Do not use these appliances if any part has been under

The brass square surround kit can be retrofitted onto previously installed appliances. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. OPERATION AND CARE OF YOUR APPLIANCE OPERATION AND CARE OF YOUR APPLIANCE Appliance operation may be controlled through the optional ON/OFF unit rocker switch, located in the lower control compartment, or through a remotely located optional wall switch or wall thermostat. Separate switches may provide independent control for the forced air blower and remote fireplace

Turn on gas supply and test for gas leaks, using a gas leak test solution (also referred to as bubble leak solution). Note: Using a soapy water solution (50% dish soap, 50% water) is an effective leak test solution but it is not recommended, because the soap residue that is left on the pipes/ fittings can result in corrosion over time. Never use an open flame to check for leaks. A. Light the appliance (refer to safety and lighting instructions on pages 18 and 19) (See *Note). Figure 12 Gas Stub

Locate the three (3) tabs at the bottom edge of the door frame into the three (3) brackets at the base of the fireplace front opening. Lean the door frame back towards the fireplace ensuring that the frame seats evenly as it draws shut. Install the three (3) 1/4"-20 x 1" Phillips pan head screws removed previously and tighten to secure. Ensure that the tab on the bottom of the door frame engages the door switch. Make sure the screws are tightened equally to avoid torquing the door (Figure 21). S

2). Replace ODS/pilot assembly or get pilot serviced. F. Thermocouple damaged. Replace thermocouple. G. Control valve damaged. Replace control valve. 7. Burner does not light after ODS/pilot is lit. A. Burner orifice is clogged. Clean burner or replace burner orifice. B. Burner orifice diameter is too small. Replace burner orifice. C. Inlet gas pressure is too low. Contact local gas company. 8. Delayed ignition of burner. A. Manifold pressure is too low. Contact local gas company. B. Burner orif

WARNING: FAILURE TO POSITION THEPARTS IN ACCORDANCE WITH THESEDIAGRAMS OR FAILURE TO USE ONLYPARTS SPECIFICALLY APPROVED WITHTHIS HEATER MAY RESULT IN PROP- ERTY DAMAGE OR PERSONAL INJURY. Flame Appearance REFER TO THE OPERATING INSTRUCTIONS LOCATED AT THE BACK OF THIS MANUAL BEFORE LIGHTING THE HEATER TO OBSERVE THE FLAMES. Flames from the pilot, front and rear burner should be visually checked as soon as the heater is installed. In addition a periodic visual check of the flames should be made.

Refractory Liner Kit One of the most beautiful enhancements you can make to this appliance is the addition of refractory liners. The refractory liner kit includes tan ceramic fiber panels for the rear and side walls of the firebox. The ceramic fiber panels have brick-like features in relief. To install the three panels, simply place them in position against the firebox walls. This kit can be retrofitted into previously installed appliances. Screen Panel Kit An optional fixed fine mesh screen pan

WARNING: THESE APPLIANCES AREDESIGNED TO OPERATE ON NATURALOR PROPANE GAS ONLY. THE USE OFOTHER FUELS OR COMBINATION OFFUELS WILL DEGRADE THE PERFOR- MANCE OF THIS SYSTEM AND MAY BEDANGEROUS. UNVENTED GAS ROOM HEATER SPECIFICATIONS AND TECHNICAL DETAILS Valve Regulator Pressure Gas Inlet Model No. Gas Type Maximum BTU/HR Operation Ignition Setting Pressure VF4000-CHN-2 Natural 25,000 Manual Piezo 5" w.c. Max 10 ..." w.c. VF4000-CMN-2 Min. 6" w.c. VF4000-CHP-2 Propane/ 25,000 Manual Piezo 10" w.c

Connect the gas line before the firebox is enclosed in the finished wall. Gas line holes and other openings should be caulked with high temperature caulk or stuffed with unfaced fi berglass insulation. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream of the heater to prevent moisture and contaminants from passing through trap to the heater controls and burners. Failure to do so could prevent the heater from operating reliably. An externa

Connect the gas line before the firebox is enclosed in the finished wall. Gas line holes and other openings should be caulked with high temperature caulk or stuffed with unfaced fi berglass insulation. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream of the heater to prevent moisture and contaminants from passing through trap to the heater controls and burners. Failure to do so could prevent the heater from operating reliably. An externa