Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. 4. Turn the Fan on by selecting the desired speed with the knob on the side of the Fan. (Figure 1A) 0 - Off 3 - High 2 - Medium 1 - Low 5. To adjust the vertical angle, push the Fan body forward or backward to the desired position. It is normal to hear a clicking sound while performing this function. (Figure 1) Breaker Reset: A 10-amp breaker is provided a

THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY. WARNING: FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. 2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer ma

The unit can be turned back on by pressing the Power Button. Figure 2 Rev. A 6/05 3 THERMOSTAT: Pressing the ( ) or ( ) button allows you to set the desired temperature of the Heater. (Figure 3) 1. Press the ( ) to increase the desired set temperature or press the ( ) to decrease the desired set temperature. 2. When the air temperature reaches 2° above the set temperature, the Heater will shut off. 3. When the air temperature reaches 1° below the set temperature, the Heater will turn on. NOTE:

Do not place on soft surfaces, like a bed, where openings may become blocked. 12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. Do not run Power Cord under carpeting. Do not cover Power Cord with throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over. 13. This Heater is HOT when in

14. A Heater has hot and arcing or sparking parts inside. Do not use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This Heater is intended for general use ONLY. 15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate a Heater where it may f

Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. 4.Make certain that the room is equipped with a working smoke detector. 5. Make certain that the power source conforms to the electrical requirements of the Heater. 6. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended. 7. This appliance has a polarized plug (one blade is wider than the other). To reduce t

(See Thermostat Instructions) 10.To turn the Heater OFF, press the Power Button () and unplug the unit from the electrical outlet. The Heater will reset to . Fahrenheit after being unplugged. INFORMACION GENERAL DE SEGURIDAD Al usar artefactos electricos, siempre deben tomarse precauciones basicas para reducir el riesgo de incendio, choque electrico y lesiones a personas, incluyendo las siguientes: Lea todas las instrucciones antes de usar este Calefactor. 1.NO CONECTE EL CALEFACTOR A CUALQUIER

Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. 4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it. 5. Unplug power cord before installing, servicing, or moving the Fan. WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD. 6. This Fan must NOT be used

10.Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, or damage the Fan. Do not block or tamper with the Fan in any manner while it is in operation. 11.Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power Cord so the Fan or other objects are not resting on it. Do not run Power Cord under carpeting. Do not cover Power Cord with throw r

READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. SAVE THESE INSTRUCTIONS Rev. A 10/05 1 2084331FP GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk