Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders. Preface Thank you for purchasing this high-speed, high-accuracy assembly robot. This manual covers interfacing required when you integrate your robot system configured with the RC5 robot controller into your facilities. Before use, read this manual carefully together with related manuals to safely get the maximum benefit from you

• When the water collects to level (A) in the pump reservoir, the drain pump begins to operate and discharges the water. • When the water level drops below level (B), the drain A B pump will stop. NOTE: • If for any reason the water level exceeds that of level (A) in the pump reservoir, an overflow Drain Switch will stop the compressor operation. • If the Fan Mode Control DIP Switch (see pg.13) has been set from the COOL to the STOP position, the Fan will also turn off while the drain pump is di

All rights reserved. This book may not be reproduced or copied, in whole or in part, without the written permission of the publisher. DENSO SALES CALIFORNIA, INC. reserves the right to make changes without prior notice. MovinCool is a registerd trademark of DENSO Corporation. OPERATION MANUAL OFFICE PRO 18 ii Table of Contents FOREWORD ..................................................................................... 1 Definition of Terms ......................................................

• The Office Pro 36 is equipped with a six (6) foot (1.8 meter) AFCI power cord. If replacement, fixed location (hard wired) or power cord lengthening (extension cord) cords are required, contact your reseller or a qualified licensed electrician for approved replacement methods. • Never fold, or place heavy objects on the power cord. This could result in damage to the power cord causing electrical shock or fire. • Do not place water or any other liquid on the unit. This can cause damage to the u

(SET POINT temperature equals inlet air or room temperature.) The unit has been preset at the factory for continuous fan operation. • Temperature Scale Display DIP Switch The Temperature Scale Display DIP Switch changes the temperature(s) that are displayed to either °C or °F. The unit has been preset from the factory to display the temperature(s) in °F. NOTE: If you wish to change the fan mode operation (COOLOPERATE to COOLSTOP), and/or the Temperature Scale Display (°F to °C), contact your Mov

. AM/PM LED Illuminates to indicate AM or PM time of day. . Program RUN Activates/deactivates a program. Button . Program SET Allows the user to program the unit or Button check the current program. START TIME LED Illuminates to indicate the current step END TIME LED that is being programmed into the unit. SET CLOCK LED CLOCK/TIMER Allows the user to set the clock and program Buttons the start and end time of operation. 9 OPERATION (cont.) Operating in COOL Mode . The unit can be operated in COO

RETAINER FILTER 17CLIP CLIPVELCRO® ATTACHMENT POINTS FILTER DAILY INSPECTION & MAINTENANCE (cont.) Filter Cleaning Method . Remove dust from the element with a vacuum cleaner, or rinse in cold or lukewarm water. If the element is extremely dirty, wash with a neutral detergent. . After the element has been cleaned, rinse with clean running water, allow to dry, then FILTER reinstall. In-Season/Off-Season Inspection & Maintenance ¦ In-Season . Check the prongs and surface of the power cord plug for

A55537 © 1999 DENSO SALES CALIFORNIA, INC. All rights reserved. This book may not be reproduced or copied, in whole or in part, without the written permission of the publisher. DENSO SALES CALIFORNIA, INC. reserves the right to make changes without prior notice. MovinCool is a registerd trademark of DENSO Sales California, Inc. SERVICE MANUAL CLASSIC PLUS 26 FOREWORD This manual has been published to service the MovinCool Classic Plus 26. Please use this service manual only when servicing the Cl

No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders. Preface Please READ through these operating instructions carefully. It will enable you to operate your CU-7011 correctly. After you have finished reading the instructions, keep this manua

If dust and/or dirt are present, wipe off with a clean, dry cloth. . Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. . Clean the air filters. . Empty all water from the drain tank. 16 TROUBLESHOOTING Self-Diagnostic Codes Self-Diagnostic Codes will be displayed on the Control Board under the following conditions: Code Condition dF When the evaporator thermistor disengages the compressor. FL When t