High unit temperatures can damage the unit, void the warranty or ignite creosote deposited in the chimney system by previous, slow burning fires. . The natural draft that pulls air through this unit and allows the fire to burn uses the indoor air of the dwelling for combustion, unless the unit is connected to an outside combustion air source. Kitchen range vent hoods, furnaces and other air movement appliances in the home are often also removing air from the dwelling; if the amount of air filtra

Keep children, furniture, fixtures and all combustibles away from any heating appliance. SAFETY NOTICE Failure to follow these instructions can result in property damage, bodily injury or even death. For your safety and protection, follow the installation instructions outlined in this manual. Contact your local building or fire officials about restrictions and installation inspection requirements (including permits) in your area. SAVE THESE INSTRUCTIONS Manufactured By: England’s Stove Works, In

and ULC.S629 (650°C) for Canada. . This wood burning unit is only listed for installation with 6.0” diameter chimney connector and chimney systems. Installing this unit on prefabricated chimneys larger than 6.0” diameter will result in decreased draft and the potential for poor unit performance. . Follow all venting system manufacturer’s installation requirements and required clearances. . Use three sheet metal screws at each single wall chimney connector joint (check manufacturer’s recommendati

If you install your stove in the same room as the Cold Air Return from your home’s Central Furnace, you must place your stove at least 20 feet (20’) from the Cold Air Return. We recommend you open an outside window slightly, and never close the door that leads from this room to the rest of your home. IN THE EVENT OF SMOKE-BACK 1. If you see smoke coming out of your unit into the room due to a power failure, DO NOT OPEN THE HOPPER OR DOOR TO YOUR UNIT!! Remain calm. Open the nearest outside door

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have been thoroughly cooled. Page | 23 DAILY MAINTENANCE DAILY MAINTENANCE Ash Removal and Disposal • Press the “Off” button and allow the stove to complete the shut-down cycle and cool completely. • Grasp the heat exchange cleaning rod located at the middle of the decorative room air grill and repeatedly pull it in and out until ash stops falling from

This unit must be installed in accordance with the following detailed descriptions of venting techniques; not installing the stove in accordance with the details listed here can result in poor stove performance, property damage, bodily injury or death. England’s Stove Works is not responsible for any damage incurred due to a poor or unsafe installation. If questions arise pertaining to the safe installation of the stove, our Technical Support line (800-245-6489) is available. Contact your local

• Before using an existing chimney, be certain it is in good condition (A chimney sweep inspection is highly recommended). Also, make sure the chimney meets the minimum standards listed in NFPA 211 (A chimney professional can confirm this upon inspection). • If connecting this stove to a factory built chimney, it may ONLY be a 6” flue, UL103 HT venting system. Connection to any other factory built chimney may result in a poorly operating or dangerous stove installation. • When connecting to an e

Once the pilot is burning, by looking from the front of the stove you can see a flame -- this small, yellow tipped, blue flame should be visible when the main burner is not operating. When the main burner is on, it is evident from the larger visible flame in the firebox. The main burner will now respond to the thermostat setting. Pilot Flame Size Firebox Flame Size B. Smoke and Odor There will be some visible smoke and some odors coming from the stove with the first few fires. These are caused b

It is recommended that insulated 18-gauge wire be used to achieve optimal performance (ten feet of wire is furnished with the thermostat). If the thermostat has to be placed farther away from the stove, it is recommended that a larger gauge wire be used. It is a good idea to leave some extra wire behind the stove so the unit can be moved out for cleaning. Mount the thermostat level for proper operation, and follow the manufacturer’s directions for installing this part. Text Box: Text Box: Approp

Install the flue cover plate on the rear opening of the unit using the supplied bolts, nuts and washers. Next, find the vent safety shut-off switch inside the draft hood on the back of the stove. It is the small disc-shaped object screwed to an L-shaped bracket; there are two (2) sets of holes on this bracket. Position this vent safety shut-off switch as far up in the flue as possible, or in a direction heading toward the ceiling. This is accomplished when the lower set of holes in the bracket i