All rights reserved. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz Up to 6 dB of boost is capable at this frequency With +6dB of boost, the woofer has more output down to 23 Hz the overall usable output is increased Figure 8 Figura 8 Abbildung 8 Figure 9 Figura 9 Abbildung 9 AMPLIFIeR WIRInG Power Connections • Power connections accept up to 4 AWG wire • 4 AWG power and ground wire recommended for optimal performance • Connect 12V+ to the battery

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

All rights reserved. 13 NOTE: Make sure all the equipment in the system is turned off when making or breaking connections to the input RCA’s or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections. Power for systems with a single amplifier can be supplied by most automotive electrical systems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly reco

(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum

• When routing wires through metal panels and doorjambs always use vinyl tubing and grommets for protection and a professional-looking installation. © 2004 Directed Electronics, Inc FIGURE 6—CONNECTION/ADJUSTMENT SINGLE AMPLIFIER BREAK AWAY RIM The model SX570 speaker has a break away rim to facilitate mounting as either a 6 X 8 or a 5 X 7 speaker. The mounting size required varies depending on the vehicle manufacturer. Break away the plastic using a pair of pliers. Use care not to damage the sp

• Check behind panels for clearance of metal brackets, hoses, and wire harnesses before making any cuts. • When mounting speakers into doors, roll the window up and down to check clearance of the glass and window regulator. • Make sure the mounting holes are the correct size for the speaker. Undersized holes can cause speaker distortion or shorting of the speaker leads to the chassis ground. Oversized holes will not allow the mounting screws to make sufficient contact with the panel, allowing th

Directed Electronics has been the industry leader in high-quality automotive security and audio equipment since 1990, and with the introduction of the Directed SX line of high-quality loudspeakers for the automobile, Directed continues to set new standards of performance, reliability, and affordability in the mobile electronics industry. Featuring silk dome tweeters, a shallow injection molded basket with metallized polypropylene vacuum-formed cones and neodymium motors, the Directed SX line of

Units which are found to be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but may be replaced at the absolute/sole discretion of DEI. ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND DEI NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME

This feature is designed into the 6500 to eliminate system turn-on pops that can occur when several components turn on at the same time. 2. ( ((+ ++) ))1 112 22V VV C CCo oon nns sst tta aan nnt tt P PPo oow wwe eer rr - This is the main power input for the 6500 and must be connected to a (+)12V constant power supply. DO NOT connect this to a switched 12V source or the system may pop when the key is turned off. 3. R RRe eem mmo oot tte ee T TTu uur rrn nn O OOn nn I IIn nnp ppu uut tt - This is

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2002 Directed Electronics, Inc FRONT PANEL CONNECTIONS/STATUS LED