Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • iMEMS ADXL345 Inertial Sensor Datalogger and Development Board FEATURES Ultralow power ADXL345 accelerometer Inertial sensor development board Datalogs onto MicroSD card Fully programmable via serial interface; firmware examples provided Battery-powered for portable applications REQUIREMENTS 2 AAA batteries MicroSD card and card reader (for datalogging) Computer with serial port (for programming) Figure1.Inertial

Ensure that Jumper JMP3 is positioned for PC control. 2. Verify that all five jumpers are in place on Connector P2. 3. Set the S1, S2, and S3 dip switch positions to high. 4. Select 622.08 MHz for the input frequency in the REF A (MHz) box in the main window of the evaluation software (see Figure 4 and the Reference Input Boxes section for more information). 5. Select 622.08 MHz for the output frequency in the Output Loop Config: box in the main window of the evaluation software (see Figure 4).

Populate R406 and R407 with 0 . resistors and remove R415 and R416 to disconnect the default clock path inputs. In addition, populate C405 and C406 with a 0.1 .F capacitor and remove C409 and C410 to disconnect the default clock path outputs. The AD9515 has many pin- strappable options that are set to a default mode of operation. Consult the AD9515 data sheet for more information about these and other options. PDWN To enable the power-down feature, short P303 to the on position (AVDD) on the PDW

1 24 RETI return from int. 1 24 AJMP addr11 jump 2 24 LJMP addr16 3 24 SJMP rel 2 24 JMP @A+DPTR 1 24 JZ rel jump if A = 0 2 24 JNZ rel jump if A not 0 2 24 CJNE A,direct,rel compare andjump if notequal 3 24 CJNE A,#data,rel 3 24 CJNE Rn,#data,rel 3 24 CJNE @Ri,#data,rel 3 24 DJNZ Rn,rel decrement and jump if not zero 2 24 DJNZ direct, rel 3 24 NOP no operation 1 12 CLR C clear bit to zero 1 12 CLR bit 2 12 SETB C set bit to one 1 12 SETB bit 2 12 CPL C complement bit 1 12 CPL bit 2 12 ANL C,bit

Connect the included power supply along with the CLK and AIN signal sources to the two evaluation boards. Then connect to the PC via the USB port and evaluate the performance instantly. 2. USB Port Connection to PC. PC interface is via a USB 2.0 connection (1.1 compatible) to the PC. A USB cable is provided in the kit. 3. 64 kB FIFO. The on-board FPGA contains an integrated FIFO to store data captured from the ADC for subsequent processing. 4. Up to 644 MSPS SDR/800 MSPS DDR Encode Rates on Each

A TCP/IP stack with integrated device driver and example code is provided in VisualDSP++® release 4.0. This evaluation kit was designed with an emphasis on modularity and expandability. With this EZ-KIT Lite, users can learn more about Analog Devices ADSP-BF537 hardware and software development and quickly prototype applications. The EZ-KIT Lite includes an ADSP-BF537 processor desktop evaluation board along with an evaluation suite of the VisualDSP++ development and debugging environment that i

02062-9106 a Copyright Information ©2007 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Limited Warranty The EZ-KIT Lite evaluation system is warranted against defects in materials and workmanship for a period of one year from the date of purchase from Analog Devices or from an authorized dealer. Disclaimer Analog Devices, Inc. reserves the right to change this product

02062-9106 a Copyright Information © 2009 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents

2 Checklist...................................................... .......................................... 2 IMPORTANT SAFETY INSTRUCTIONS.................................. ... 3 Connecting Your VoIP ATA....................................... .......................... 3 Accessing your ATA Web Panel................................... ..................... 3 VoIP / SIP Configuration Setup through Web Panel............... 4 Upgrading Your Firmware........................................ ........