Remove the protective paper from the charcoal filter that you will find in the accessories pack. From inside the cabinet, position the filter in the round box located in the top back of the cabinet. Arrange the shelves to suit your convenience (see section 6.) Wait 48 hours before switching the cabinet on so as to allow the fluids to settle. If you need to move the Wine Vault, do not tip over 45 degrees, and only tip towards the back of the unit. Make sure you can access the plug of the unit for
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Connecting To Power Supply The Wine Vault’s power cord is equipped with a plug which fits into any standard socket with grounded connection, to prevent any risk of shock. Have the power outlet checked by a qualified electrician to make sure it is actually grounded. If this is not the case, you must have it replaced with a socket which is suitably gr
Cooling Technology You can also register your Amcor purchase online, and view our broad selection of innovative products. Table of Contents Table of Contents Thank You ……………………………………………………… 2 Safety Instructions ……………………………………………… 3 Your Wine Vault ………………………………………………… 4 Installation …………………………………………………… 5-6 Installing in Cabinet or with Decorative Door ………………… 6 Temperature Settings ………………………………………… 7-8 Layout & Storage ……………………………………………… 9-12 Care & Maintenance ……………………………………………13 Troubleshooti
Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. 1. Open kit and remove new parts. 2. Insert the new metal thermostat well into the small, non flared end of the tube and seal it with V to V2 inch of food grade silicone. Let set for 15-30 minutes. 3. Turn the machine off. 4. Remove panels, as needed. 5. Gently pull gray sensing bu
Retain these instructions as part of your equipment manual. INSTALLATION PROCEDURE FOR FLAT FLOOR DRAINS 1. Mount the wire form support in the center of the floor drain grid and clamp it s four legs of the support onto the drain grid securely. If necessary, reform the legs to fit and attach firmly to the drain grid. The clamps are omitted for clarity on the first two illustrations. 2. Place the plastic splashguard collar over the wire form support. 3. The adjustable clamps will accomodate 1/
Mild Dish Detergent and 2” Brush Required FIGURE 2. Remove Cap and Nozzle Adapter and Clean with Hot Water and Mild Dish Detergent using the Brush. Replacement Parts Replacement parts are available for sale by calling Bevcore at (866) 275-6392 or by ordering online at evco re.com Replacement Part Numbers: • Complete tank assembly with lid: 720401107 • Replacement lid only: 720202010 Release Date: July 18, 2006 © 2006, IMI Cornelius Inc. - 1 - Revision: B Publication Number: 729011175IN
Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. 1. Raise and lock driptray assembly (see Figure 1). Driptray Assembly Figure 1. 2. Clean out and dry driptray with a rag or paper towel, remove strainer if applicable (see Figure 2 and Figure 3). Upper Driptray Assembly Figure 2. Clean and Wipe Dry Inside Driptray Figure 3. Revisi
Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. T\ WARNING: All of the attachment screws and plates must be installed as directed in this manual. Failure to comply could result in serious Injury, Death or Damage to the equipment. Revision Date: August 3, 2010 © 2006-2010, IMI Cornelius Inc. - 1 - Revision: B Publication Number: 629088733INS IDC Icemaker Adaptor Kit Installation Ins
3.3 Condenser Dissipates heat from the compressor and prepares the high pressure refrigerant for the capillary tube and ultimately the evaporator. 3.4 Condenser Cleaning It is very important to do this on an annual basis and as required. The condenser can be cleaned with a brush or compressed air. There are commercial condenser cleaners on the market that are acceptable. 3.5 Filter Replacement The Jet Spray unit comes with a foam type filter mounted on the inside of the side panel assembly. JT30
BE CAREFUL TO SECURELY HOLD DRAIN LINE TO AVOID DAMAGE TO UPPER DRIPTRAY!!! Cut PVC Drain Figure 5. 5. Deburr edge of PVC and re-plumb and clamp with new flexible tube/clamp supplied in kit (see Figure 6). MAKE SURE THAT THE INSULATION COVERS ALL EXPOSED TUBING/CLAMP! Figure 6. 6. Re-route new drain tube to floor drain. MAKE SURE THAT THERE ARE NO KINKS IN NEW DRAIN LINE! 7. Re-install driptray strainer if applicable. 8. Check driptray, fittings, and lines for leaks. 9. Lower upper driptr