Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: (001) 8

Do not forget to include your name, address and a daytime telephone number. Alternatively, you can contact our freephone service hot-line on the number given below. Office hours are as follows: Mon - Fri: 8 am - 6 pm, Sat: 10 am - 2 pm, Sun: 10 am - 4 pm UK / NORTHERN IRELAND HELPLINE: 0870 7323023 REPUBLIC OF IRELAND HELPLINE: 1800 481005 WEB SUPPORT: Omega, Interex House, Prospect Close, Lowmoor Business Park NG17 7LF Kirkby In Ashfield, England Replacements or repairs under guarantee regulati

• If required, the plunge depth can be set accurately to within 0.1 mm. • Retighten button 9. Adjustment using the revolver- depth stop The revolver-depth stop enables you to quickly choose between six different cutting depths. These are also determined by the adjustment of the depth stop (10). • Adjust the required cutting depth by rotating the revolver-depth stop (21). Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 15 Helpline No.

6.2.1 Pumping in the FLOW RATE Mode To pump fluid in the FLOW RATE Mode, do the following: 1. Set up the pump motor for pumping, according to Chapter 3. 2. Toggle the ON/OFF switch to turn on the unit’s power. The display is in the STOPPED Display Mode. Refer to Figure 6-3. 3. Either set the TUBE ID for the tube you are using (following Section 5.3) or calibrate the tube (following Section 5.5), before continuing. 4. Press the FLOW RATE key. FLOW RATE Display shows xxx mL/min ACTION Displays cur

Table 9-2 in Chapter 9, shows the average flow rates for different size tubing. Normalized flow rates (mL per revolution) vary significantly, based on motor speed, tubing materials, viscosity, and mechanical tolerances in pump dimensions. Table 9-3 outlines the variances resulting from differences in motor speed, tubing materials, and mechanical tolerances. Table 9-6 outlines the variances due to differences in viscosity. To determine the chemical compatibility of a particular tubing material, i

INSTALLING.....................................................................................................................................4 2.1 LAYOUT...........................................................................................................................................4 2.2 JUMPER SETUP..................................................................................................................................5 2.2.1 JP0 ~ JP15 Analog Input R/C Filter ...............

Rectangular shaped metal liner available for on-site Wood Hood construction, Figure 4. 4. The ventilation system (power module and ducting system) is not included and must be purchased separately. B. Installation: Metal Liner - T-Shaped, Figure 3 1. Measure up 6 1/8 from the bottom of adjacent cabinets. Scribe a level line horizontally across depth of both cabinets. 2. Raise Metal Liner so that bottom edge of liner is level with scribed lines. Use four (4) #8 x 1/2” screws provided to attac

OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exc

Normal system filtrsitions should be sufficient. Systems which do not have any filtration should be equipped with at least a 200 m6sh sjeve or 74 micron filter. Most hydraulic systems would already have a much finer filtration. Within the cartridge dirt or sealing agents, such as Teflon tape, may lodge within and cause malfunction. If a malfunction does occur and you are using proper filtration, we would recommend disassembly and cleaning. This Can be done as follows: On clean bench, remove sm

These units feature an SPDT switch, which can be triggered at any point along the flow range FEATURES • Strong, completely sealed die cast aluminum body, water and oil tight • Forrped double sealed aluminum cover (with lip) anodized • Unbreakable Lexan window (full cover) • Oversize neoprene cover gasket matches with double ribbed lip of die cast body. Other seals — Buna-N • Chrome plated pan head cover screws with screw retainers • Wire guards • Easy wire top screw micro switch • Mount