The information provided in this document has been carefully checked and is accurate at the time of publication. However, the Manufacturer assumes no responsibility for any infringements of patents or other rights of third parties that may result from its use. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form of or via any means without the prior written permission of the Manufacturer. Further, this publication and features described herein a

The Choice: 3T, 2T, 4T, Reserved. u RAS TO CAS DELAY This item defines SDRAM ACT to Read/Write command period. The choice: 3T, 2T, 4T, Reserved. u DRAM BACKGROUND COMMAND This item is lead-off time control for DRAM background command. When select 'Delay 1T', background commands are issued 1 clock behind memory address (MA) been issued. When select 'Normal', background command and MA are issued at the same time. The choice: Delay 1T or Normal. 7-118 APOLLO 120/150 III User Manual version 2305 u L

CN4: PCI/ISA Expansion Slot The PC 610 provides an ISA/PCI slot for ISA and PCI device expansion. F1 F2 F3 F4 F5 F6 F7 F31 H1 H2 H3 H4 H19 B1 B2 B3 B4 B5 B6 B7 B31 D1 D2 D3 D4 D18 E1 E2 E3 E4 E5 E6 E7 E31 G1 G2 G3 G4 G19 A1 A2 A3 A4 A5 A6 A7 A31 C1 C2 C3 C4 C18 CN4: PCI/ISA Slot Side 6-91 APOLLO 120/150 III User Manual version 2207 CN4: PCI/ISA Slot Connector Pin Assignment Pin Signal Pin Signal Pin Signal Pin Signal F1 GND B1 GND E1 GND A1 IOCHK F2 GND B2 ISARST E2 GND A2 SD7 F3 INTB B3 VCC E3

Back Panel Assembly The back panel module is the last module to be integrated to the APOLLO main system before the plastic housing is to be installed to the system. 1. On the I/O board, there are 6 D-SUB connectors with 2 bronze sticks on each side. Remove the 12 bronze sticks. 2. Insert the I/O board to the I/O bracket (2) and fix them together with the 12 bronze sticks. Fix them again with 2 screws on the other side. 3. Fix the complete I/O module to the metal back panel (1) five FMS 3*5 screw

3 Applications .............................................................. 4 Pre-Installation Checklist ........................................ 5 Parts Identification ................................................... 6 Operator Installation ................................................ 7-9 Pivot Arm Installation Actuator Installation Control Box Installation Connecting the Actuator Gate Bracket Installation Limit Switch Adjustment Control Board Connections Control Board Adjustments - Le

This hard shutdown condition can only be reset by shorting the FIREBOX or UL connectors on the left side of the circuit board to ground. If a firebox is used in the installation, The firebox door should be opened and closed to reset the circuit board. Once the operator is installed or if the control board is replaced, you will need to program the control board for proper current sensing. The operator should be functional and the open and close limits set. 1. Push and hold the LED ENABLE button f

The LARGE knob will select the higher level Nav functions: Nav pages, Parallel Track Offset, GPS Position, Countdown Timer, and the FROM/TO/NEXT Waypoints. The SMALL knob will look at the pages available for each function; a diamond (·) will be shown on the lower, right side of the display if more pages are available. The Nav Home Page is a default page that is the first page available in the Navigation function. The Nav Home Page is not customizable. The information in the Home Page shows the D

© 2001 by UPS Aviation Technologies, Inc. All rights reserved. Printed in the U.S.A. UPS Aviation Technologies, Inc. Consumer Products Division 2345 Turner Road, S.E. Salem, OR 97302 U.S.A. Toll Free 800.525.6726 Canada Toll Free 800.654.3415 International 503.391.3411 FAX 503.364.2138 Visit our web page at Send comments about this manual by email to: techpubs@at.ups.com Welcome ... Welcome to a new era of aviation navigation. Once again, II Morrow Inc. has set new standards in features and ease

Interval for saving Track History . Strategy (Full/Forever) . Percentage of memory used (status only) 1. In the Map function, turn the LARGE knob to reach the Map Setup page. Turn the SMALL knob to the first Track History page. Press SEL to start editing the waypoint types. Pressing the TRK and SAV smart keys toggle the available options. Pressing the INTV smart key enables selection of the interval value. SEL Moving Map Functions Trk History:Off Save By:Distance Interval:0.5 2. Turn the SMALL k

3 Marian Lane Brodheadsville, PA 18322 Issue date: 12/05/08 TABLE OF CONTENTS 1) Introduction 2 2) Unpacking the Apollo monoblocks 2 3) Connecting the Apollo monoblocks 3 4) Operation of the amplifiers 4 5) Setting the tube bias 5 6) Troubleshooting 7 7) Registration card 8 8) Fuse values 8 9) Specifications 8 10) Warranty 9 INTRODUCTION Congratulations on your purchase decision! We at Rogue Audio truly believe that our amplifiers provide the “smartest” value in high-end audio. If you have never