The Main dialog box will appear. 2. Click Setup - Devices. The Devices dialog box appears. 231 Figure 4.1: Devices Dialog Box After you assign a device type to a secondary switch, the port numbering changes. In the above example, Port 2-1 is a secondary port. The 2 indicates the port number on the primary switch and 1 is the port number on the secondary switch. To assign a device type: 1. In the Devices dialog box, select the port number. 2. Click Modify. The Device Modify dialog box appe

The maximum length should not exceed 10 meters (32.8 feet). WARNING: Always disconnect power before changing any wiring. To reduce the risk of electric shock or damage to the equipment, this product must be installed in accordance with the following guidelines. This product is intended to be connected to a DC power source that can be classified as a secondary circuit in accordance with applicable national requirements for Information Technology Equipment. Generally, these requirements are base

The switch uses this information to initialize the keyboard and mouse interfaces of the servers. If the servers are turned on before the switch, the servers may exhibit abnormal or erratic behavior. To power up the OutLook switch system: 1. Turn on the monitors. 2. Turn on the primary switch. 3. Turn on the servers attached to the primary switch. 4. Turn on the secondary switch (if applicable). 5. Turn on the servers attached to the secondary switch (if applicable). Checking the OutLook s

Mount components beginning at the bottom of the rack, then work to the top. Do not exceed your rack load rating. 10 OutLook ES Series Installer/User Guide CAUTION Power Considerations: Connect only to the power source specified on the unit. When multiple electrical components are installed in a rack, assure the total component power ratings do not exceed circuit capabilities. Overloaded power sources and extension cords present fire and shock hazards. To install the switch mounting bracke

2 No. 950, EN60950, IEC 60950 FCC part 15A, EN55022, EN55024 Table of Contents Chapter 1: Product Overview OutLook ES Features and Benefits.................3 Safety Precautions..............................5 Chapter 2: Installation Getting Started.................................9 Rack Mounting your OutLook ES Unit.............9 Installing a 4- or 8-Port Switch ..................11 Installing a 16-Port Switch......................13 Installing a Multiple Switch System...............15

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation o

DANGEROUS VOLTAGE This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. POWER ON This symbol indicates the principal on/off switch is in the on position. POWER OFF This symbol indicates the principal on/off switch is in the off position. PROTECTIVE GROUNDING TERMINAL This symbol indicates a terminal which must be connected to earth ground prio

To select the server to include in your scan pattern, use the following keyboard commands in the Name, Port or Sec column: a Press Alt+Down Arrow to move the cursor down the list of servers. b Press Alt+Up Arrow to move the cursor up the list of servers. c Press Alt+Home to move the cursor to the first server listed. d Press Alt+End to move the cursor to the last server listed. 2. In the Sec column, type the number of seconds (from 1 to 99) of desired Delay Time before the scan moves to the ne

• Test AC outlets at the computer and monitor for proper polarity and grounding. • Use only with grounded outlets at both the computer and monitor. When using a backup power supply (UPS), power the computer, the monitor and the AutoView 424 unit off the supply. NOTE: The AC inlet is the main disconnect. Rack mount safety considerations • Elevated Ambient Temperature: If installed in a closed rack assembly, the operation temperature of the rack environment may be greater than room ambient. Use ca

5 Recommended configuration......................................................................................................5 Cable/network specifications...................................................................................................... 6 Remote Power Control option....................................................................................................6 Installing the Digital Desktop System......................................................................