All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS Construction Injection molded polypropylene plastic housing and tube blower Fan blower type Totally enclosed fan cooled white polypropelene fan Motor Unit 110-120 Volts AC, 60 Hz Motor Power Peak2100 Watts, 20.8 Amps Power Speed Control Dial Con

2. Locate the top of the belt idler assembly where the clutch cable (item 55) is secured in place. A properly tensioned belt should stretch the idler spring (located next to the idler pulley) between 1/4" -3/8" when the clutch bail (item 54) is held in the drive position. 3. Using a 1/2" wrench loosen the two nuts that secure the cable (item 55) in place. 4. TO INCREASE belt tension adjust these two nuts so that the cable (item 55) is secured in place with an additional 1/4" of the threaded adju

NOTE: Engage the clutch bail to use the front wheel drive to aid in turning the unit. TRANSPORT: Be sure to lift the tine engagement lever (tine out of the ground) before transporting away from the work area. HANDLING & TRANSPORTING CAUTION: This unit is heavy. It requires at least two people to lift it. REMOVE: The aerator is equiped with a removable rear weight. Remove the weight when loading and unloading the unit. The weight can be removed by rotating the locking tabs on the weight mounting

Set the air compressor to 30 - 100 working PSI. Do NOT exceed 110 PSI. 3. Squeeze Air Blow Gun trigger to begin the flow of air. 4. Release Air Blow Gun trigger to stop the flow of air. 5. When finished, turn off the air compressor and then disconnect Air Blow Gun from the air source hose 6. Only use clean and dry compressed air. Never use oxygen, carbon dioxide, combustible gases or any other bottled gas as a power source. 92363 951 59 For technical questions and replacement parts, pleas

830180 1 830180 1 830180 1 10 Belt Traction Drive 500119 1 500119 1 500119 1 11 Plate Pivot Idler / Shifter 500122 1 500122 1 500122 1 12 Shifter Pivot WA 500169 1 500169 1 500169 1 13 Pulley Idler 800260 1 800260 1 800260 1 14 Wheel & Tire 16" AG SP LH 500103 1 500103 1 500103 1 15 Wheel & Tire 16" AG SP RH 500104 1 500104 1 500104 1 16 Arm Idler WA 500170 1 500170 1 500170 1 17 Cable Clutch Blade BC2400 500259 1 500259 1 500259 1 18 Cable Clutch Drive BC2400 500146 1 500146 1 500146 1 19 Bar S

(See trouble shooting pushing the machine. section on page 12). CLEARING A CLOGGED CUTTING DECK: ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. PUT OIL IN ENGINE BEFORE STARTING. 16.1 STARTING Turn engine off and wait for blade to stop completely. Disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire. BLADE CLUTCH Engine must be level when checking and filling oil and

RECONNECT SPARK PLUG WIRE, AND ALL GUARDS BEFORE START- ING ENGINE. Note: Blade, and drive belts are normal wear items. These should be inspected on a regular basis and replaced if worn. ENGINE When servicing engine refer to specific manufacturers engine owner's manual. All engine warranty is covered by the specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer for service it is a good idea to have

Operator’s controls are shown below. 1 2 3 5 6 7 4 Operator Control Locations STARTING 1 2 3 4 Blade Clutch Lever 5 Gear Shift Lever 6 Choke 7 Throttle ON/OFF Switch Drive Clutch Lever Pull Starter CHECK engine oil level before operating machine. 1. Place equipment on a level, firm surface that is free of rocks or other debris. 2. Place throttle in START position. Throttle Part No 500264 11 F091506B BC2402 Series Brush Cutter Owner’s Manual 3. Pull choke out (Honda engine only). 4. Choke Units e

Tests were performed on 5-25-2006 under the conditions listed below. General Conditions: Sunny Temperature: 72.32oF(22.4oC) Wind Speed: 3.8 mph (6.12kph) Wind Direction: East Humidity: 62.2% Barometric Pressure: 29.9Hg (101.3kpa) INTENDED USE INTENDED USE: This machine is designed for removing thatch from your lawn, renovation of existing lawns, and to assist in overseeding operations. The machine should not be used for any other purpose than that stated above. Do not operate if excessive vibrat