CHECK OIL LEVEL OFTEN DURING ENGINE BREAK-IN. A. POSITION EQUIPMENT SO ENGINE IS LEVEL. B. Clean area around oil fill plug (see Figure 1). C. Remove oil fill plug and dipstick. D. Wipe dipstick clean, insert it into oil fill hole and tighten securely. Remove dipstick. If oil is not up to “FULL” mark on dipstick, add recommended oil. POUR SLOWLY. Wipe dipstick clean each time oil level is checked. IMPORTANT: DO NOT FILL ABOVE “FULL” MARK ON DIPSTICK. E. Install oil fill plug and dipstick, t

[4] Established in 1933 as an agricultural equipment manufacturer, Standard Gas Engine Works was purchased by John Buhler in 1969. Through steady expansion, new products and acquisitions, the company has experienced steady growth and has evolved into one brand name: Buhler. Over the years, many brands have joined the Buhler family: Farm King, Allied, Inland and Versatile. Buhler maintains several well-stocked parts warehouses and is committed to continuous product improvement and incorporating n

I standard Cat. I std Cat. II std Cat. II std Cat. II std Cat. II std Cat. II bushings Cat. II Q.H. std Cat. II Q.H. std Cat. III Q.H. std Cat. III Q.H. std Cat. I & II heavy Cat. III Q.H. narrow Cat. III Q.H. narrow Cat. III Q.H. narrow Cat. III Q.H. narrow frame optional Hitch adjustment 4 position 4 position 2 position 2 position Fixed 2 position 2 position HP requirement 15 - 30 20 - 40 40 - 70 60 - 90 90 - 125 120 - 180 120 - 180 Weight 422 lbs 470 lbs 756 lbs 966 lbs 1243 lbs 2398 lbs 2314

BE SURE ENGINE IS COOL. DO I NOT SMOKE.__ Run engine until fuel tank is empty and engine stops due to lack of fuel. NOTE: If “Gasohol” has been used, complete above instructions and then put 1/2 pint of unleaded gasoline into fuel tank and repeat above instructions. NOTE: Tecumseh "SMART START"™ gasoline preservative and stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE EQUIPMENT ON WHICH THIS ENGINE IS USED BEFORE ATTEMPTING TO OPERATE YOUR TECUMSEH ENGINE. A THESE SYMBOLS ^ \/\ MAY APPEAR ON ▼ (STOP) THE ENGINE. FAST SLOW STOP CHOKE IGNITION KEY ™ run TO RUN [i-Q REMOVE TO STOP | \V_L PRIMER ^4 California Proposition 65 AVARNINGr • The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

After you read the warranty, ask your dealer to explain any points that you may not understand. This tractor was designed to power and propel itself. It is intended for use in normal and customary agricultural applications. Do not modify or alter or permit anyone else to modify or alter this tractor or any of its components or any tractor function without first consulting an authorized Buhler Versatile dealer. If you have any questions regarding tractor modifications, contact Buhler Versatile In

TURN SIGNALS Move the stalk to position 1 to indicate a right-hand turn. Move the stalk to position 4 to indicate a left-hand turn. The turn signal warning light (and trailer lights, if connected) will also flash when the signals are operated. HEADLIGHTS HIGH/LOW BEAMS With the headlights switched on, pull the stalk to position 3, to change from one beam to the other beam. HEADLIGHT FLASH With low beam headlights on, pull the stalk to position 2, to flash the high beams. Release the stalk to ret

4. Insert hitch pin and be sure the retainer is in the latched position. NOTE: For implements that require hitch extensions or interfere with the tractor clevis, remove and store the clevis and hitch pin. Always use a safety chain installed between the tractor and implement hitch when transporting equipment on the highway. North American standards recommend that you observe the following precautions for towing equipment not equipped with brakes: DO NOT TOW equipment weighing more than twice the

18. Fill the cooling system with a 50/50 blend of low silicate antifreeze and clean soft water. Add coolant slowly through the radiator filler neck until the coolant is to the bottom of the filler neck. NOTE: To avoid trapping air in the system, fill the radiator as slowly as practicable thereby allowing any air pockets to disperse. 3-59 SECTION 3 -LUBRICATION AND MAINTENANCE EVERY 2400 HOURS OR 24 MONTHS (WHICHEVER OCCURS FIRST) 19. Fill the coolant recovery tank, 1, to the lowest mark, 2. 20.

The “+/–(SET)” button, 2, adjusts the cruise setting. When cruise mode is activated, the engine returns to the last cruise setting, if possible, based on throttle lever position. The cruise function can be set to any engine RPM, but the operating cruise RPM cannot exceed the normal RPM for the current throttle position. For example, if the cruise setting is 1800 RPM but the hand throttle is at a normal 1700 RPM position, cruise will not increase the RPM. On the 2360/2425 models equipped with the