FOV (ft. @ 100 yds.) 1 2 1 Congratulations on the purchase of your Bushnell Night Vision Product. Bushnell Night Vision products are comprised of high quality image intensifier tubes and optics. Bushnell Night Vision products amplify existing light, allowing you to see in dark conditions too dark for the naked eye. HOW NIGHT VISION WORKS Bushnell Night Vision products collect and amplify existing light through the objective lens, which is then focused on the image intensifier. Inside the intensi

LUXEON® LED’s deliver the brightest solid state lighting available. Unlike typical conventional light sources, LED’s are brighter, energy efficient, and long lasting. The LED never needs replacement and will function for 100,000 hours. These Bushnell LED performance lights are o-ringed sealed and waterproof. BaTTERy INSTaLLaTION / REPLaCEMENT Remove the end cap by rotating counter clock-wise. require two CR123 3-volt Lithium Batteries. 3-watt models with the LUXEON® III LED (10-0100, 10-0200, an

Unlike typical conventional light sources, LED’s are brighter, energy efficient, and long lasting. The LED never needs replacement and will function for 100,000 hours. These Bushnell LED performance lights are o-ringed sealed and waterproof. BaTTERy INSTaLLaTION / REPLaCEMENT Remove the end cap by rotating counter clock-wise. require two CR123 3-volt Lithium Batteries. 3-watt models with the LUXEON® III LED (10-0100, 10-0200, and 10-0300) If batteries are not inserted Insert battery positive end

require two CR123 3-volt Lithium Batteries. 3-watt models with the LUXEON® III LED (10-0100, 10-0200, and 10-0300) If batteries are not inserted Insert battery positive end first and Insert both batteries positive end first and replace end cap. correctly, the unit will not light. 1-watt models (10-0090) using a LUXEON® I LED only require one CR123 3-volt lithium battery. replace end cap. 3-WaTT LED OPERaTION (Models 10-0100, 10-0200, 10-0300) To power the light on, first depress the power switch

In Europe you may also contact Bushnell at: BUSHNELL Outdoor Products Gmbh European Service Centre MORSESTRASSE 4 D- 50769 KOLN GERMANY Tel: +49 (0) 221 709 939 3 Fax: +49 (0) 221 709 939 8 This warranty gives you specific legal rights. You may have other rights which vary from country to country. ©2006 Bushnell Outdoor Products 6 7 Flashlight 6LIM.indd 8-9 3/24/06 11:55:41 AM 8 Flashlight 6LIM.indd 10-11 FRaNcaIS INTRODUCTION : Votre lampe-torche DEL de Bushnell est une lampe de premiere qualit

Whereas standard incandescent and LED lights produce circular patterns of light that are nonuniform irregular “blobs” of light, the HD High Definition Light provides 165 lumens of consistent light intensity from center to edge. HD ADVANTAGES • HD allows for cleaner finite reading and makes objects stand out from their background. • Makes locating lost objects much easier by using the “quadrant / zone search method” • Prevents shadows unlike conventional lights BATTERY INSTALLATION / REPLACEMENT

4. Press SNAP to take a picture, or press the MODE button quickly to change mode settings as described above. The camera is set at infinity and will not be focused on an object closer than 49 feet. 5. The mode setting operation is a cycle loop, so press the MODE button to switch to another mode. The loop order of the different modes is shown here: 6. To change settings, toggle through the different modes by pressing the MODE button. When a mode is selected, the indicator symbol on the LCD will a

Turn the camera on by pressing and holding the MODE button until the display comes on and the camera beeps. To turn the unit off, press and hold the MODE button until the display goes out. The camera will turn itself off automatically to save batteries if none of the buttons have been pressed for three minutes. ADJUST THE BINOCULAR FOR COMFORTABLE VIEWING Adjust the center focus wheel (located between the eyepieces on the bottom of the camera) while viewing a distant object through the binocular

To avoid any flickering on the picture, the correct power frequency (either 50 or 60) for your country must be selected. 15. If "Delete Last" mode is selected, the display will show the following: delete last picture then quit this mode Press SNAP to delete the last picture from the camera’s memory. 16. If "Delete All" mode is selected, the word "ALL" appears next to the icon on the display. To delete all pictures in the camera’s memory, select this mode. The picture number will then blink. Pres

If you choose to work this way, from a connected camera, be sure that you save the photo (when you are done editing) to your hard drive, and not the camera’s memory or card. To do this in PhotoSuite, after clicking “Done”, answer “Save Changes?” with “Yes”, but then answer “Replace Existing File”? with “No” and use the “Save As” dialog box to save the edited photo in a folder on your hard drive (“Save In>Local Disk”), not the “Removable Disk” (camera). 8. If you are new to photo editing on a com