WARNING – Failure to install and operate the charger in accordance with these instructions may result in damage to the charger or injury to the operator. 2. WARNING – Never place the charger directly above or below the battery being charged. Gases or fluids from the battery will corrode and damage the charger. Locate the charger as far away from the battery as the output cable allows. 3. WARNING – Explosive gases may result from charging. Provide adequate ventilation during charging. Prevent fla
1-3 Wiring Instructions.............................................Pp. 4,5 Operating Instructions....................................... Pp. 6,7 Fast-Cast 175 Schematic Assembly.................. P. 8 Fast-Cast 175 Assembly & Wiring Instructions.. Pp. 9-11 Drop Utility Mount Schematic Assembly............ P. 12 3-Point Hitch Mount Schematic......................... P. 13 Fast-Cast 2000 Schematic Assembly................ P. 14 Fast-Cast 3000 Schematic Assembly................ P. 15 Drive Assembl
All external connections must have dielectric grease. 2. Read lead labels before attaching to power source or ground. 3. No other devices may be spliced into wiring harness. 4. Any repairs to wiring harness must be done with heat shrink butt connectors. 5. If inline fuse is installed, use a 35 amp slow blow (Fast-Cast 2000 and Fast-Cast 3000), and use a 60 amp slow blow fuse for Fast-Cast 4000 only. Item No. Part No. Description Qty. 1CS1P39 Male Splice Cord - 18” 1 1CS1P38 Female Splice Cord
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. WATER AND MOISTURE - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. ACCESSORIES - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fal
Amplitude 44-55g, half sine, 9-13 msec duration. 9 Vibration Meets SAE J 1378 March 83. Double amplitude of 1.53 mm with frequency sweep from 10-80-10 Hz (20 g max) at intervals of 1 minute. ! Humidity 95% RH (non-condensing) at +38C Water/dust immunity Face IP63 Rear IP50 Salt spray (fog) ASTM B 117-73 as per SAE J1810, section 4.7.1.2 10 ! 4. INSTALLATION Terminal Assignment for Models 2111R, 2112R, 2113R 1 Sender in 2 Battery + 3 Ground 4 Sender low (optional: for use with two wire senders) 5
Installation and startup must be performed by skilled personnel. Failure to install and operate the unit in accordance with these instructions may result in damage or injury. If safe operation of the instrument can no longer be ensured, stop and secure it against accidental operation. If instrument failure or malfunction may cause personal injury or material damage, use additional safety measures such as limit switches, guards, etc. Read the Operating Instructions carefully before startup. ! ! N
This will determine what your proper wire length is to be. 2. Run spreader/vehicle harness from the rear of vehicle to switch area. Remove approx. 3'' of the black outer jacket exposing two single leads (red and black), strip a 1/4'' off each lead. Crimp 1/4'' female connector on red lead and crimp the butt connector to the black lead. Place the female spade/red wire to the on/off switch and leave the black wire for the next step. 3. Route the power harness from the battery to the switch; this w
Swing Away - Pivot Mount Installation Instructions Step 1. Insert upper & lower pivot rails into main frame of spreader. Line up the pre-punched holes on the pivot rail with the main frame, then bolt together. Holes are pre-determined and can be relocated if spreader is not centered on vehicle. Step 2. Locate top bed rail mounting brackets and set on top of pickup bed rails; Center by moving out towards the bumper. Maintain a minimum of 2” clearance between tailgate and spreader. Step 3. Locate
Software for formatting internal memory. Portable Media Player Your Pocket Guide Portable Media Player Install SoftwareGet ConnectedTransfer MediaPlug Your Ears & Enjoy Your Pocket Guide System Requirement System Requirement You’ll need a computer with: Windows® 98/98SE/ME/2000/XP/Vista Pentium Class or faster Processor CD-ROM Drive 64MB RAM 30MB free hard disk space USB Port Software Installation Software Installation Software Utilities Installation Insert the CD into the CD ROM drive of your P