Manual Storage Slot: A convenient slot in the base has been provided to insert the manual for future reference. Volume Control: Turn the volume control clockwise to increase the volume or counterclockwise to decrease the volume. Reset Button: This button has a dual purpose. 1) To return to the first tune in a Group when using the Tune Selection Button to cycle through the tune selections. 2) To reset the chime in case of power failure or surge. Cover Pin: A notched cover pin is located on two si

9. Twist together the wires labeled “C” and secure them with a UL approved wire nut. 10.Place chime cover securely over base (see Figure 5). 11. Restore power. Press push button(s) to test chime. 4 598-1142-01 REPLACEMENT INSTALLATION WIRING For replacing an existing transformer, see instructions supplied with transformer. WARNING: Turn power off at fuse or circuit breaker before installing transformer. 1. Verify existing chime/bell system works correctly. If no sound is heard, see Troubleshoot

IMPORTANT: The chime will operate with a front door connection only. The chime will not operate properly with just a rear door pushbutton installed. © 2003 DESA Specialty Products™ 598-1142-01 RESET SCROLL TUNESELECTION REARTUNE 12 12 3 4 5 6 7 8 9 OFF GROUP SELECTION 74 BASE Screw/Tornillo/Vis Wire Entrance Hole/Orificio de entrada del cable/Orifice d’entree des fils Manual Holder/ Portamanual/ Porte-guide Cover Pins/Sujetadores de la tapa/Agrafes de couvercle Mounting Hole/ Orificio de montaje

• The non-electric chime mounts directly through the door and will accommodate door thicknesses of 3/4" to 2". • The chime is equipped with a viewer. Locating the door chime 1. Mount the chime in the center of the door approximately 4 1/2 feet to 5 feet above the floor. Note: Be sure there are no obstructions on the inside of the door to interfere with the chime’s baseplate. 2. Using the template provided, mark the location of the mounting holes parallel to the edge of the door (see Figure 1). N

Plug wireless chime into wall outlet. Note: The volume control is on the back of the wireless chime. Unplug chime to adjust volume. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to bypass this safety feature. ©

No Service Parts Available for this Product Regulatory Information This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance

In typical use, alkaline batteries will last up to three years. 1. Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Make sure battery is oriented properly (See page 4). 2. Install3alkaline“D”batteries. Make sure batteries are oriented Figure 1 + + + BatteryBatteryBattery Chime Volume Jumpers - - - properly (see Figure 2). 3. Test range. Temporarily position chime and push button Cover where you want th

• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A2

In typical use, alkaline batteries will last three years. 3.Test Range. Temporarily position chime where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 1. Open chime case: Press in catch on bottom of chime and lift the case open. Battery Chime Volume 2. Install the 3 alkaline "D" batteries. Make sure batteries are oriented properly. 4. Mount accessory chime. Chime can be mounted by using 3 holes in the back of c