B) To attach LOWER LINK ARM to PEDAL ARM, slide SPACER (J), FLAT WASHER (K) and WAVY WASHER (L) onto PEDAL ARM BRACKET. NOTE: Attaching the lower link arm assembly to the pedal arm first makes assembly of the linkage arms less difficult. C) Slide LOWER LINK ARM onto PEDAL ARM BRACKET, followed by FLAT WASHER (M) and BOLT (N). D) Repeat on other side. E) Slide LOWER LINK ARM onto UPPER HANDLEBAR and attach using 2 PRE-ATTACHED SET SCREWS. F) Attach HANDLEBAR COVERS using 2 SCREWS (O). G) Repeat o

It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To p

Place your bike on a level flat surface. It is recommended that you place a protective covering on your floor. You will only need to attach the following items. Verify that the following parts and tools are included: Parts • 1 Rear Foot Tube • 1 Handlebar Set • 1 Seat Post • 1 Seat • 1 Console Mast • 1 Console Mast Boot • 2 Mobile Wheels • 1 Console • 2 AA Batteries • 2 Pedals • 2 Wheel Sleeves • 1 Tension Knob • 1 Hardware Pack (contents listed below) E) 18mm Arc Washer Quantity: 2 F) 14mm Wash

If the pacer wins, the console will flash and scroll PACER WINS, you will finish your race and begin your cool-down. 22 USING YOUR THR ZONE PROGRAMS 1 & 2 (3.1B only) The THR zone program is designed to keep the user at an optimum exercise level, while adjusting the resistance levels to keep the user at a target heart rate. To choose the THR zone program, follow these instructions. 1. Choose the THR zone program by pressing the quick program buttons. Press ‘SELECT’. 2. Determine your target THR

.................... ................ .......... ............ HARDWARE BAG FOR STEP 2 CONTENTS : Elite 1.2E 2.2E Rev.1.0.indd 12-13 7/19/05 8:20:32 AM 14 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES BEFORE YOU BEGIN ASSEMBLY 15 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY A) Open HARDWARE BAG FOR STEP 3. B) S

View the time remaining or the time elapsed in your workout. INCLINE • Shown as Percent. Indicates the incline of your walking or running surface. HEART RATE • Shown as Beats Per Minute. Used to monitor your heart rate (displayed when contact is made with both pulse grips or wireless chest strap is used) DISTANCE • Shown as Miles. Indicates distance traveled during your workout. SPEED • Shown as MPH. Indicates how fast your walking or running surface is moving. CALORIES • Total Calories bur

It is recommended that you place a protective covering on your floor. You will only need to attach the following items. Verify that the following parts and tools are included: Parts • 1 Rear Foot Tube • 2 Handlebar Set • 1 Seat Post • 1 Seat • 1 Console Mast • 1 Console Mast Boot • 2 Mobile Wheels • 1 Console • 2 AA Batteries • 2 Pedals • 2 Wheel Sleeves • 1 Tension Knob • 2 Handlebar Links • 1 Hardware Pack (contents listed below) E) 13mm Nut Quantity: 2 J) 14mm Washer Quantity: 2 K) 20mm Bolt

Your new Horizon Fitness upright bike will help you eliminate the obstacles that prevent you from getting in your exercise time. Inclement weather and darkness won't interfere with your workout when you use your Horizon Fitness upright bike in the comfort of your home. This manual provides you with basic information for using and enjoying your new machine. A more complete knowledge of your new Horizon Fitness upright bike will assist you in realizing your goal of a healthy lifestyle. 6 Console H

Note: Make sure not to tighten bolts until all assembly steps have been completely assembled and aligned. STEP 2: ATTACH LEFT & RIGHT GUIDE RAILS. STEP 3: ATTACH CONSOLE MAST AND CONSOLE MAST BOOT. Note: Make sure to loosen the water bottle screws in order to fit the console cable through the mast. DO NOT PINCH WIRES! STEP 4: ATTACH LEFT & RIGHT PEDAL ARMS AND PEDAL ARM SLEEVES. Note: Black ‘Teflon’ surface of K should be facing the pedal arm. STEP 5: ATTACH LEFT & RIGHT LOWER HANDLE BARS TO CON