TABLE OF CONTENTS A. Introduction.............................................................................................4 1. Unpacking...........................................................................................4 2. Product Overview AndPrinciple Of Operation..........................................4 B. Installation...............................................................................................5 1. General Considerations.........................................

M-4271/0707, pg. 6 of 26 2. Mounting the Flow Controller. The FMA 3200/3400 Series controllers have no particular orientation or installation requirements so may be mounted in any convenient position. It is recommended that units be fixed to a suitable substrate using the two 4-40 mounting holes provided. Mounting View from Bottom (mounting hardware not includedwith sensor) 3. Tubing Connections All tubing must be clean, dry and purged with clean dry air before installation of the FLO-CONTROLLER

An optional 0-5VDC Input / Output Power Adapter Package is available for use with the FMA 3200/3400 Series. This consists of a power source (115VAC or 230VAC), a connection hub and two cable assemblies with pigtail (soldered wire) ends. This should be assembled as shown in the following diagram. Assembling a FMA 3215PWPower Adapter Package (the FMA 3223PW Power Adapter Package is similar) The RED connector should be inserted in the RED socket on the connection hub. The WHITE connector should be

9. Changing the Calibration Gas – FMA 3400/3400ST Series Only The FMA 3400/3400ST Series may be calibrated for up to three gases. These gases, their corresponding flow ranges and accuracy specifications are detailed on the calibration certificate. The calibration gas required is determined by selecting the corresponding dip switch on the front panel of the display. M-4271/0707, pg. 17 of 26 FMA 3400/3400ST Series Dip Switches Dip switch 4 is allocated to the primary calibration gas. Dip switch 5

Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment. • The use of attachments not recommended or sold by the manufacturer may cause fire, electrical shock or injury. • DO NOT use outdoors. • DO NOT let cord hang over edge of table or counter, or touch hot surf a c e s . • Always make sure juicer cover is clamped securely in place before motor is turned on. DO NOT unfasten clamps while juicer is in operation. • Be sure to turn

Always begin use at a reduced sensitivity level; increase sensitivity only after you have become familiar with the detector. 2) Do not use indoors. This detector is for outdoor use only. Many household appliances emit electromagnetic energy, which can interfere with the detector. If conducting an indoor demonstration, turn the sensitivity down and keep the search coil away from appliances such as computers, televisions and microwave ovens. If your detector beeps erratically, turn off appliances

Return appliance to the nearest authorized service facility for examination, repair, or electrical adjustment. ¦ The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock, or injury. ¦ DO NOT use outdoors. ¦ DO NOT let cord hang over edge of table or counter. ¦ Always make sure juicer cover is clamped securely in place before motor is turned on. ¦ Be sure to turn switch to off position after each use of your juicer. ¦ DO NOT put your fingers or other objec

Omega Products, Inc. Harrisburg, PA 17111-4523, U.S.A. Phone: (717) 561-1105 Fax: (717) 561-1298 E-mail: OMEGA@omegajuicers.com IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: • Read all instructions. • To protect against risk of electrical shock, do not put the motor base in water or other liquid. • Close supervision is necessary when any appliance is used by or near children. • Unplug from outlet when not in use

For All Non-Juicing Functions STEP 1 Place the auger into the drum. Insert the blank into the drum with the protruding tab at the bottom. Insert the appropriate nozzle into the inside of the Drum Cap. Place the drum cap onto the drum end and turn it counterclockwise until it is firmly in place. STEP 2 Connect assembled drum set with main body by inserting the visible part of the metal shaft into the hex area on the main body. Secure by turning the locking clip clockwise. Place the hopper onto th

. and that of your family. It is important that you take a few moments to read the following instructions and suggestions to get the most out of your Omega Juicer and to completely understand what it can do. Your Omega Juicer is simple to operate and maintain. It has been constructed of the highest- quality material and all-stainless steel parts, built to provide a lifetime of delicious, healthful fresh fruit and vegetable drinks. We feel confident that your Omega Juicer will provide you with ma